Investigation of batch fluidized-bed drying by mathematical modeling, CFD simulation and ECT measurement

Mathematical modeling, computational fluid dynamics (CFD) analysis and electrical capacitance tomography (ECT) is used to develop an understanding of batch fluidized-bed drying, which is a complex air-solids, multiphase process. The mathematical model is based on a three-phase theory that describes the mass-and heat-transfer between the air and solids phases. The CFD model is based on a two-fluid model (TFM) approach, in which both phases are considered to be continuous and fully interpenetrating. The hydrodynamic parameters used to model the heat-and mass-transfer between the two phases are determined by a correlation approach, and the estimated parameters are incorporated into a user defined function (UDF) in FLUENT. The moisture diffusion in the air and solids phases is simulated using the user defined scalar (UDS) transport equation in the software package. ECT is used for the online solids concentration and moisture measurement, based on dynamic calibration. Comprehensive comparisons between results from mathematical modeling, CFD simulation and ECT measurement are presented, and are validated using experiment results. Online measurement of moisture content is compared with a static calibration. The mathematical model, CFD and ECT presented are being integrated into an online process control system for a batch fluidized-bed drying application in the pharmaceutical industry. © 2007 American Institute of Chemical Engineers AIChE J, 2008

[1]  S. E. Aly,et al.  A three phase model of a batch fluidized bed , 1999 .

[2]  Akira Nonaka,et al.  A generalized bubble diameter correlation for gas‐solid fluidized beds , 1987 .

[3]  R. Jackson,et al.  Frictional–collisional constitutive relations for granular materials, with application to plane shearing , 1987, Journal of Fluid Mechanics.

[4]  Tomasz Dyakowski,et al.  Application of capacitance tomography to gas-solid flows , 1997 .

[5]  V. Vanec̆ĕk,et al.  Fluidized bed drying , 1966 .

[6]  C. Srinivasa Kannan,et al.  A kinetic model for drying of solids in batch fluidized beds , 1994 .

[7]  Wuqiang Yang,et al.  A new image reconstruction method for tomographic investigation of fluidized beds , 2002 .

[8]  K. Viswanathan,et al.  Model for continuous drying of solids in fluidized/spouted beds , 1986 .

[9]  D. Gidaspow,et al.  A bubbling fluidization model using kinetic theory of granular flow , 1990 .

[10]  Sang-Done Kim,et al.  Mathematical model for batch drying in an inert medium fluidized bed , 1999 .

[11]  Béla Paláncz,et al.  A mathematical model for continuous fluidized bed drying , 1983 .

[12]  Andrzej Kmiec,et al.  CFD modeling of heat and mass transfer in a spouted bed dryer , 2004 .

[13]  Andrzej Kmiec,et al.  Point-by-point solution procedure for the computational fluid dynamics modeling of long-time batch drying , 2005 .

[14]  Robert Mattes,et al.  In-line Process Analysis of Residual Moisture in a Fluid Bed Granulator-Dryer Using NIR , 2005 .

[15]  Todd Pugsley,et al.  The dynamic calibration of an electrical capacitance tomography sensor applied to the fluidized bed drying of pharmaceutical granule , 2005 .

[16]  Tom Dyakowski,et al.  Study of bubbling and slugging fluidized beds by simulation and ECT , 2006 .

[17]  D. Jeffrey,et al.  Kinetic theories for granular flow: inelastic particles in Couette flow and slightly inelastic particles in a general flowfield , 1984, Journal of Fluid Mechanics.

[18]  Ian C. Kemp,et al.  Computational fluid dynamics modelling of vertical pneumatic conveying dryers , 1991 .

[19]  Bo G Leckner,et al.  Two- or three-dimensional simulations of turbulent gas–solid flows applied to fluidization , 2001 .

[20]  Lorraine Young.  Moisture Measurement Using Low Resolution Nuclear Magnetic Resonance , 1989 .

[21]  L. T. Fan,et al.  Modelling and simulation of a continuous fluidized-bed dryer , 1986 .

[22]  N. Subramanian,et al.  Three-phase model for gas flow in fluidized beds , 1982 .

[23]  L. R. Glicksman,et al.  Semi-empirical prediction of bubble diameter in gas fluidized beds , 1981 .

[24]  Dimitri Gidaspow,et al.  Fluidization in Two-Dimensional Beds with a Jet. 2. Hydrodynamic Modeling , 1983 .

[25]  R. Jackson,et al.  Gas‐particle flow in a vertical pipe with particle‐particle interactions , 1989 .

[26]  R. J. King,et al.  Microwave moisture measurement of grains , 1991 .

[27]  D. Gunn.  Transfer of heat or mass to particles in fixed and fluidised beds , 1978 .

[28]  Wuqiang Yang,et al.  Investigation of fluidised bed drying by combination of CFD and ECT , 2006 .

[29]  J. Rantanen,et al.  On-line monitoring of moisture content in an instrumented fluidized bed granulator with a multi-channel NIR moisture sensor , 1998 .

[30]  Liang-Shih Fan,et al.  ECT imaging of three-phase fluidized bed based on three-phase capacitance model , 2003 .

[31]  Wuqiang Yang,et al.  New AC-based capacitance tomography system , 1999 .

[32]  C.R.E. de Oliveira,et al.  A numerical investigation of bubbling gas–solid fluidized bed dynamics in 2-D geometries , 2002 .

[33]  San Kiang,et al.  Can pharmaceutical process development become high tech , 2006 .

[34]  F. Hamdullahpur,et al.  MATHEMATICAL MODELLING OF SIMULTANEOUS HEAT AND MASS TRANSFER IN FLUIDIZED BED DRYING OF LARGE PARTICLES , 1999 .

[35]  Wuqiang Yang,et al.  Adaptive calibration of a capacitance tomography system for imaging water droplet distribution , 2004 .

[36]  Norollah Kasiri,et al.  Mathematical modeling of a continuous fluidized bed dryer , 2006 .

[37]  Wuqiang Yang,et al.  Modelling of batch fluidised bed drying of pharmaceutical granules , 2007 .

[38]  Wuqiang Yang,et al.  Electrical capacitance tomography with square sensor , 1999 .

[39]  Avi Levy,et al.  Two-Fluid, Two-Dimensional Model for Pneumatic Drying , 2003 .

[40]  C.R.E. de Oliveira,et al.  A study of bubbling and slugging fluidised beds using the two-fluid granular temperature model , 2001 .

[41]  Roland Clift,et al.  CONTINUOUS BUBBLING AND SLUGGING. , 1985 .

[42]  Ajl Harrison,et al.  Bubble distribution and behaviour in bubbling fluidised beds , 2007 .

[43]  D. Geldart.  Types of gas fluidization , 1973 .