Process development for additive manufacturing of functionally graded alumina toughened zirconia components intended for medical implant application

[1]  T. Moritz,et al.  Lithography-based ceramic manufacturing (LCM) – Viscosity and cleaning as two quality influencing steps in the process chain of printing green parts , 2017 .

[2]  Tassilo Moritz,et al.  Ceramic-Based 4D Components: Additive Manufacturing (AM) of Ceramic-Based Functionally Graded Materials (FGM) by Thermoplastic 3D Printing (T3DP) , 2017, Materials.

[3]  G. Adabo,et al.  The effects of mechanical and hydrothermal aging on microstructure and biaxial flexural strength of an anterior and a posterior monolithic zirconia. , 2017, Journal of dentistry.

[4]  O. Lyckfeldt,et al.  Influence of Resin Composition on the Defect Formation in Alumina Manufactured by Stereolithography , 2017, Materials.

[5]  T. Moritz,et al.  Micro-Reactors Made by Lithography-Based Ceramic Manufacturing (LCM) , 2016 .

[6]  Umesh N. Gandhi,et al.  Design and fabrication of periodic lattice-based cellular structures , 2016 .

[7]  Paolo Colombo,et al.  Additive Manufacturing of Ceramics: Issues, Potentialities, and Opportunities , 2015 .

[8]  Wolfgang Wachter,et al.  Light curing strategies for lithography-based additive manufacturing of customized ceramics , 2014 .

[9]  Peter Greil,et al.  Additive Manufacturing of Ceramic‐Based Materials , 2014 .

[10]  Rainer Telle,et al.  Novel Prospects and Possibilities in Additive Manufacturing of Ceramics by means of Direct Inkjet Printing , 2014 .

[11]  A. Afzal.  Implantable zirconia bioceramics for bone repair and replacement: A chronological review , 2014 .

[12]  Mazen Al-Hajjar,et al.  Wear of novel ceramic-on-ceramic bearings under adverse and clinically relevant hip simulator conditions. , 2013, Journal of biomedical materials research. Part B, Applied biomaterials.

[13]  J. Wiltfang,et al.  A comparison of biocompatibility and osseointegration of ceramic and titanium implants: an in vivo and in vitro study. , 2012, International journal of oral and maxillofacial surgery.

[14]  Thomas Oberbach,et al.  Kinetic of the Phase Transformation of ATZ Compared to Biograde Y-TZP , 2007 .

[15]  Claus Emmelmann,et al.  Rapid manufacturing of lattice structures with selective laser melting , 2006, SPIE LASE.

[16]  L. Gibson.  Biomechanics of cellular solids. , 2005, Journal of biomechanics.

[17]  S. Seal,et al.  Mechanisms of room temperature metastable tetragonal phase stabilisation in zirconia , 2005 .

[18]  Thomas Oberbach,et al.  ATZ – A New Material with a High Potential in Joint Replacement , 2005 .

[19]  J. Chevalier,et al.  Low‐Temperature Aging of Y‐TZP Ceramics , 2004 .

[20]  K. Shakesheff,et al.  In vitro assessment of cell penetration into porous hydroxyapatite scaffolds with a central aligned channel. , 2004, Biomaterials.

[21]  A. Eichler,et al.  Tetragonal Y-doped zirconia: Structure and ion conductivity , 2001 .

[22]  Vijay Chandru,et al.  Voxel-based modeling for layered manufacturing , 1995, IEEE Computer Graphics and Applications.

[23]  Tassilo Moritz,et al.  Additive Manufacturing of Ceramic Heat Exchanger: Opportunities and Limits of the Lithography-Based Ceramic Manufacturing (LCM) , 2017, Journal of Materials Engineering and Performance.

[24]  Tassilo Moritz,et al.  Thermoplastic 3D Printing—An Additive Manufacturing Method for Producing Dense Ceramics , 2015 .

[25]  Thierry Chartier,et al.  Rapid Prototyping of Ceramics , 2013 .

[26]  E. Mecher,et al.  Effect of hydrothermal aging on zirconia crystal phases and strength , 2010 .

[27]  R. Danzer,et al.  The ball on three balls test—Strength and failure analysis of different materials , 2007 .