A high-performance cathode for the next generation of solid-oxide fuel cells

Fuel cells directly and efficiently convert chemical energy to electrical energy. Of the various fuel cell types, solid-oxide fuel cells (SOFCs) combine the benefits of environmentally benign power generation with fuel flexibility. However, the necessity for high operating temperatures (800–1,000 °C) has resulted in high costs and materials compatibility challenges. As a consequence, significant effort has been devoted to the development of intermediate-temperature (500–700 °C) SOFCs. A key obstacle to reduced-temperature operation of SOFCs is the poor activity of traditional cathode materials for electrochemical reduction of oxygen in this temperature regime. Here we present Ba0.5Sr0.5Co0.8Fe0.2O3-δ(BSCF) as a new cathode material for reduced-temperature SOFC operation. BSCF, incorporated into a thin-film doped ceria fuel cell, exhibits high power densities (1,010 mW cm-2 and 402 mW cm-2 at 600 °C and 500 °C, respectively) when operated with humidified hydrogen as the fuel and air as the cathode gas. We further demonstrate that BSCF is ideally suited to ‘single-chamber’ fuel-cell operation, where anode and cathode reactions take place within the same physical chamber. The high power output of BSCF cathodes results from the high rate of oxygen diffusion through the material. By enabling operation at reduced temperatures, BSCF cathodes may result in widespread practical implementation of SOFCs.

[1]  Sano,et al.  A low-operating-temperature solid oxide fuel cell in hydrocarbon-Air mixtures , 2000, Science.

[2]  Brian C. H. Steele,et al.  Appraisal of Ce1−yGdyO2−y/2 electrolytes for IT-SOFC operation at 500°C , 2000 .

[3]  Zongping Shao,et al.  Investigation of the permeation behavior and stability of a Ba0.5Sr0.5Co0.8Fe0.2O3−δ oxygen membrane , 2000 .

[4]  Meilin Liu,et al.  Novel Cathodes for Low‐Temperature Solid Oxide Fuel Cells. , 2002 .

[5]  John B. Goodenough,et al.  Increasing Power Density of LSGM-Based Solid Oxide Fuel Cells Using New Anode Materials , 2001 .

[6]  T. Ishihara,et al.  La-Doped BaCoO3 as a Cathode for Intermediate Temperature Solid Oxide Fuel Cells Using a LaGaO3 Base Electrolyte , 2002 .

[7]  Jürgen Fleig,et al.  Solid Oxide Fuel Cell Cathodes: Polarization Mechanisms and Modeling of the Electrochemical Performance , 2003 .

[8]  Zongping Shao,et al.  Performance of a mixed-conducting ceramic membrane reactor with high oxygen permeability for methane conversion , 2001 .

[9]  C. Mirodatos,et al.  Studies on the performance stability of mixed conducting BSCFO membranes in medium temperature oxygen permeation. , 2003, Chemical communications.

[10]  M. Koyama,et al.  Reaction model of dense Sm0.5Sr0.5CoO3 as SOFC cathode , 2000 .

[11]  C. Rossignol,et al.  Cathode Materials for Reduced-Temperature SOFCs , 2003 .

[12]  Meilin Liu,et al.  A simple and cost-effective approach to fabrication of dense ceramic membranes on porous substrates , 2004 .

[13]  W. Munro,et al.  The bell inequality: A measure of entanglementa? , 2001, quant-ph/0102119.

[14]  Nigel P. Brandon,et al.  Recent Advances in Materials for Fuel Cells , 2003 .

[15]  Scott A. Barnett,et al.  Effect of LSM-YSZ cathode on thin-electrolyte solid oxide fuel cell performance , 1997 .

[16]  Sangtae Kim,et al.  Diffusion and surface exchange coefficients in mixed ionic electronic conducting oxides from the pressure dependence of oxygen permeation , 1998 .

[17]  William J. Thomson,et al.  Oxygen permeation rates through ion-conducting perovskite membranes , 1999 .

[18]  B. Steele,et al.  Materials for fuel-cell technologies , 2001, Nature.