Optimisation of electrical discharge machining process with CuW powder metallurgy electrode using grey relation theory

In this paper, an attempt has been made to correlate the usefulness of powder metallurgy (PM) electrodes in electrical discharge machining (EDM). This paper explains the same with the help of experimentation on AISID2 steel in kerosene with CuW (25% Cu and 75% W) PM electrode. An L18 orthogonal array was used to identify the effect of process parameters (viz. electrode material, duty cycle, flushing pressure and current) on the performance characteristics i.e., material removal rate surface roughness and surface hardness. A grey relation grade obtained from the grey relation analysis is used to solve the EDM process with multiple performance characteristics. Experimental results have shown that electric discharge machining process performance can be improved efficiently through this approach. It is found that copper tungsten PM electrode gives better multi-objective performance than conventional copper electrode.

[1]  Ching-Tien Lin,et al.  Surface modification using semi-sintered electrodes on electrical discharge machining , 2008 .

[2]  J. Ramkumar,et al.  Electro-discharge machining performance of TiCN-based cermets , 2007 .

[3]  Henry W. Altland,et al.  Engineering Methods for Robust Product Design , 1996 .

[4]  J. Wiedemeyer,et al.  General aspects for tribological applications of hard particle coatings , 1989 .

[5]  M. S. Shunmugam,et al.  Surface modification in electrodischarge processing with a powder compact tool electrode , 1991 .

[6]  Ching-Kao Chang,et al.  Design optimization of cutting parameters for side milling operations with multiple performance characteristics , 2007 .

[7]  N Tosun,et al.  Determination of optimum parameters for multi-performance characteristics in drilling by using grey relational analysis , 2006 .

[8]  Biing-Hwa Yan,et al.  EDM performance of Cr/Cu-based composite electrodes , 2003 .

[9]  David K. Aspinwall,et al.  Surface alloying using PM composite electrode materials when electrical discharge texturing hardened AISI D2 , 2002 .

[10]  William Y. Fowlkes,et al.  Engineering Methods for Robust Product Design: Using Taguchi Methods in Technology and Product Development , 1995 .

[11]  C. L. Lin,et al.  Use of the Taguchi Method and Grey Relational Analysis to Optimize Turning Operations with Multiple Performance Characteristics , 2004 .

[12]  Sachin Maheshwari,et al.  Some investigations into the electric discharge machining of hardened tool steel using different electrode materials , 2004 .

[13]  José Carvalho Ferreira,et al.  A study of die helical thread cavity surface finish made by Cu-W electrodes with planetary EDM , 2007 .

[14]  J. L Lin,et al.  The use of the orthogonal array with grey relational analysis to optimize the electrical discharge machining process with multiple performance characteristics , 2002 .

[15]  J. Deng,et al.  Introduction to Grey system theory , 1989 .

[16]  B. Sarkar,et al.  Performance of ZrB2-Cu composite as an EDM electrode , 2007 .

[17]  J. S. Soni,et al.  Experimental investigation on migration of material during EDM of die steel (T215 Cr12) , 1996 .

[18]  Naotake Mohri,et al.  Study on the surface modification system with electrical discharge machine in the practical usage , 2004 .

[19]  Mathews P. Samuel,et al.  Power metallurgy tool electrodes for electrical discharge machining , 1997 .

[20]  Y. Wong,et al.  EDM performance of TiC/copper-based sintered electrodes , 2001 .

[21]  Yunn-Shiuan Liao,et al.  Optimization of machining parameters of Wire-EDM based on Grey relational and statistical analyses , 2003 .

[22]  Q. Peng.  Improving abrasion wear by surface treatment , 1989 .

[23]  A. Nee,et al.  Formation of a new EDM electrode material using sintering techniques , 1999 .

[24]  M. Shunmugam,et al.  Tribological behaviour of an electrodischarge machined surface with a powder metallurgy bronze electrode , 1993 .

[25]  Wansheng Zhao,et al.  Surface modification process by electrical discharge machining with a Ti powder green compact electrode , 2002 .

[26]  K. Shu,et al.  Study of electrical discharge grinding using metal matrix composite electrodes , 2003 .

[27]  J. Halling.  Surface coatings materials conservation and optimum tribological performance , 1979 .

[28]  Y. Wong,et al.  Effect of TiC in copper–tungsten electrodes on EDM performance , 2001 .

[29]  C. Wykes,et al.  A new method of optimising material removal rate using EDM with copper–tungsten electrodes , 2000 .

[30]  P. Dickens,et al.  Using rapid prototyping to produce electrical discharge machining electrodes , 1996 .