Effect of cutting speed on the performance of Al2O3 based ceramic tools in turning nodular cast iron

Abstract This paper presents the results of an experimental investigation on the effect of cutting speed in turning nodular cast iron with alumina (Al 2 O 3 ) based ceramic tools. Three different alumina based ceramic cutting tools were used, namely TiN coated Al 2 O 3  + TiCN mixed ceramic, SiC whisker reinforced Al 2 O 3 and uncoated Al 2 O 3  + TiCN mixed ceramic tool. Turning experiments were carried out at four different cutting speeds, which were 300, 450, 600 and 750 m/min. Depth of cut and feed rate were kept constant at 1 mm and 0.1 mm/rev, respectively, throughout the experiments. Tool performance was evaluated with respect to tool wear, surface finish produced and cutting forces generated during turning. Uncoated Al 2 O 3  + TiCN mixed ceramic was the worst performing tool with respect to tool wear and was the best with respect to surface finish. SiC whisker reinforced Al 2 O 3 exhibited the worst performance with respect to cutting forces. If tool wear, surface finish and cutting force results are considered together, among the three tools studied, TiN coated Al 2 O 3  + TiCN mixed ceramic tool is the most suitable one for turning nodular cast iron, especially at high cutting speeds ( V c  > 600 m/min).

[1]  Wuyi Chen,et al.  Cutting forces and surface finish when machining medium hardness steel using CBN tools , 2000 .

[2]  A. Ghani,et al.  Study of tool life, surface roughness and vibration in machining nodular cast iron with ceramic tool , 2002 .

[3]  S. J. Burden,et al.  Ceramic Cutting Tools , 2008 .

[4]  R. Krishnamurthy,et al.  7 – Phase Transformation Toughened Materials for Cutting Tool Applications , 1994 .

[5]  Hans Kurt Tönshoff,et al.  Survey of the die and mold manufacturing industry - practices in Germany, Japan, and the United States , 1996 .

[6]  I. R. Pashby,et al.  Ceramic tool wear when machining austempered ductile iron , 1993 .

[7]  E. Degarmo.  Materials and Processes in Manufacturing , 1974 .

[8]  A. Dias,et al.  Residual stress analysis in orthogonal machining of standard and resulfurized AISI 316L steels , 1999 .

[9]  Keith Smith,et al.  6 – Alumina-Silicon Carbide Whisker Composite Tools , 1994 .

[10]  E.-G. Ng,et al.  EVALUATION OF CUTTING FORCE AND TEMPERATURE WHEN TURNING HARDENED DIE STEEL WITH AMBORITE AMB90 AND DBC50 TOOLING , 1999 .

[11]  Tae Jo Ko,et al.  Surface Integrity and Machineability in Intermittent Hard Turning , 2001 .

[12]  A. B. Sadat.  Effect of high cutting speed on surface integrity of AISI 4340 steel during turning , 1990 .

[13]  W. W. Gruss.  4 – Aluminum Oxide/Titanium Carbide Composite Cutting Tools , 1994 .

[14]  S. Avner.  Introduction to Physical Metallurgy , 1964 .

[15]  Yoshiteru Chujo,et al.  Cutting performance and wear mechanism of alumina-based ceramic tools when machining austempered ductile iron , 1994 .

[16]  C. K. Toh,et al.  Static and dynamic cutting force analysis when high speed rough milling hardened steel , 2004 .

[17]  Ibrahim Ciftci,et al.  The effect of alloying elements on surface roughness and cutting forces during machining of ductile iron , 2003 .

[18]  David K. Aspinwall,et al.  High speed end milling of hardened AISI D2 tool steel (∼58 HRC) , 2002 .

[19]  Scandvik coromant.  Modern Metal Cutting : a practical handbook , 1994 .