Multi-layered PZT/polymer composites to increase signal-to-noise ratio and resolution for medical ultrasound transducers

Increasing transducer bandwidth and signal-to-noise ratio (SNR) is fundamental to improving the quality of medical ultrasound images. In previous work, the authors have proposed the use of multi-layer 1-3 PZT/epoxy composites to increase both but have encountered significant fabrication challenges. These difficulties include making the bond thickness between the layers extremely small relative to the ultrasound wavelength and aligning the posts of the composite to increase the coupling coefficient. The authors have routinely achieved a bond thickness of less than 5 /spl mu/m but aligning the posts is more complicated. Finite element (PZFlex; Weidlinger, Assoc., New York, NY and Los Altos, CA) simulations show that the pulse-echo SNR and bandwidth degrade significantly with misalignment of the posts. Alignment of greater than 90% of the post pitch (i.e., tolerance of 10 to 20 /spl mu/m) is required to obtain significant increases in SNR and bandwidth relative to conventional transducer arrays. This will be a difficult tolerance for large-scale production. Thus, the authors have developed a multi-layer composite hybrid array that will not require post alignment. This structure consists of a layer of 5 MHz 1-3 composite material on top of conventional 5 MHz PZT, which will provide greater SNR relative to conventional composites and increased bandwidth over multi-layer PZT. PZFlex simulations show that for a 2 MHz linear array element, the 2 layer hybrid structure increases the pulse-echo SNR by 7.5 dB over that from a single layer PZT element. Even without a matching layer, an increase in the -6 dB pulse-echo fractional bandwidth from 22% for the PZT element to 35% for the hybrid element was also predicted. Experimentally, in a 32 element array, the authors achieved an increase of 5.2 dB in SNR and an increased -6 dB bandwidth from 23 to 30%. In vitro and in vivo images showed corresponding improvements.

[1]  B. Auld,et al.  Acoustic fields and waves in solids , 1973 .

[2]  Alan Robert Selfridge.  The design and fabrication of ultrasonic transducers and transducer arrays , 1982 .

[3]  L. E. Cross,et al.  Piezoelectric Composite Materials for Ultrasonic Transducer Applications. Part II: Evaluation of Ultrasonic Medical Applications , 1985, IEEE Transactions on Sonics and Ultrasonics.

[4]  J. Unsworth,et al.  Simple model for piezoelectric ceramic/polymer 1-3 composites used in ultrasonic transducer applications , 1989 .

[5]  B. Auld,et al.  Modeling 1-3 composite piezoelectrics: thickness-mode oscillations , 1991, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[6]  S.W. Smith,et al.  Multilayer piezoelectric ceramics for two-dimensional array transducers , 1994, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[7]  F. Foster,et al.  Modeling and optimization of high-frequency ultrasound transducers , 1994, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[8]  Richard L. Goldberg,et al.  Optimization of Signal-to-Noise Ratio for Multilayer Pzt Transducers , 1995 .

[9]  Multilayer piezoelectric resonators for medical ultrasound transducers , 1996, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[10]  D. Mills,et al.  Combining multi-layers and composites to increase SNR for medical ultrasound transducers , 1996, 1996 IEEE Ultrasonics Symposium. Proceedings.

[11]  C.G. Oakley,et al.  Calculation of ultrasonic transducer signal-to-noise ratios using the KLM model , 1997, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[12]  Stephen W. Smith,et al.  Finite element analysis of a deformable array transducer , 1997, 1997 IEEE Ultrasonics Symposium Proceedings. An International Symposium (Cat. No.97CH36118).

[13]  S.W. Smith,et al.  Modeling of piezoelectric multilayer ceramics using finite element analysis , 1997, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[14]  Gordon Hayward,et al.  Multilayer piezocomposite transducers for applications of low frequency ultrasound , 1997, 1997 IEEE Ultrasonics Symposium Proceedings. An International Symposium (Cat. No.97CH36118).

[15]  D. Powell,et al.  Stacked composite piezoelectric materials for 1.5-D arrays , 1997, 1997 IEEE Ultrasonics Symposium Proceedings. An International Symposium (Cat. No.97CH36118).

[16]  Processing of fine-scale piezoelectric ceramic/polymer composites for transducer applications , 1997 .

[17]  S.W. Smith,et al.  Hybrid multi/single layer array transducers for increased signal-to-noise ratio , 1997, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[18]  Najib N. Abboud,et al.  Finite element modeling for ultrasonic transducers , 1998, Medical Imaging.

[19]  S.W. Smith,et al.  Finite element analysis of a deformable array transducer , 1999, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[20]  Stephen W. Smith.  Multi-layer composite ultrasonic transducer arrays , 1999 .