Modeling for optimization of circular flat pad aerostatic bearing with a single central orifice-type restrictor based on CFD simulation
暂无分享,去创建一个
Yang Hong | Mo Jun | Li Yifei | Cui Hailong | Yin Yihui | Liu Xin’en
[1] Yoshimi Takeuchi,et al. Improvement of Machining Accuracy of 5-Axis Control Ultraprecision Machining by Means of Laminarization and Mirror Surface Finishing , 2005 .
[2] P. A. McKeown,et al. The Role of Precision Engineering in Manufacturing of the Future , 1987 .
[3] Mohamed E. Eleshaky,et al. CFD investigation of pressure depressions in aerostatic circular thrust bearings , 2009 .
[4] T. B. Stowell,et al. Pneumatic hammer in an externally pressurized orifice-compensated air journal bearing , 2003 .
[5] Lisa Poyneer,et al. Demonstrating sub-nm closed loop MEMS flattening. , 2006, Optics express.
[6] Kaiji Sato,et al. TREND OF PRECISION POSITIONING TECHNOLOGY , 2005 .
[7] D. A. Boffey,et al. A theoretical and experimental study into the steady-state performance characteristics of industrial air lubricated thrust bearings , 1985 .
[8] Shigeka Yoshimoto,et al. Numerical Calculations of Pressure Distribution in the Bearing Clearance of Circular Aerostatic Thrust Bearings With a Single Air Supply Inlet , 2006 .
[9] Nenzi Wang,et al. Multi-objective optimization of air bearings using hypercube-dividing method , 2010 .
[10] Jyh-Chyang Renn,et al. Experimental and CFD study on the mass flow-rate characteristic of gas through orifice-type restrictor in aerostatic bearings , 2004 .
[11] Xuedong Chen,et al. Air Vortices and Nano-Vibration of Aerostatic Bearings , 2011 .
[12] K. J. Stout,et al. The design of aerostatic bearings for application to nanometre resolution manufacturing machine systems , 2000 .
[13] Simon Barrans,et al. Design and test of a Pareto optimal flat pad aerostatic bearing , 2008 .
[14] Farid Al-Bender,et al. On the modelling of the dynamic characteristics of aerostatic bearing films: From stability analysis to active compensation , 2009 .
[15] R. L. Hardy. Theory and applications of the multiquadric-biharmonic method : 20 years of discovery 1968-1988 , 1990 .
[16] Wang-Long Li,et al. Grip Performance Affected by Water-Induced Wrinkling of Fingers , 2015, Tribology Letters.
[17] Terenziano Raparelli,et al. Discharge coefficients of orifice-type restrictor for aerostatic bearings , 2007 .
[18] K. J. Stout,et al. Design procedures for orifice compensated gas journal bearings based on experimental data , 1978 .
[19] Han Ding,et al. Influences of the geometrical parameters of aerostatic thrust bearing with pocketed orifice -type restrictor on its performance , 2007 .
[20] Y X Ye,et al. Effects of recess shapes on pneumatic hammering in aerostatic bearings , 2010 .
[21] Tojiro Aoyama,et al. Numerical and Experimental Analysis for the Small Vibration of Aerostatic Guideways , 2006 .
[22] Terenziano Raparelli,et al. CFD Analysis of a Simple Orifice-Type Feeding System for Aerostatic Bearings , 2015, Tribology Letters.
[23] Xuedong Chen,et al. Dynamic characteristics of ultra-precision aerostatic bearings , 2013 .
[24] Takashi Matsuoka,et al. Clarifications of the mechanism of nano-fluctuation of aerostatic thrust bearing with surface restriction , 2012 .
[25] Sadek Z. Kassab,et al. Effects of operating conditions and supply hole diameter on the performance of a rectangular aerostatic bearing , 1997 .
[26] Shigeka Yoshimoto,et al. Numerical calculation and experimental verification of static and dynamic characteristics of aerostatic thrust bearings with small feedholes , 2011 .
[27] Shigeka Yoshimoto,et al. Numerical investigation of static and dynamic characteristics of aerostatic thrust bearings with small feed holes , 2010 .
[28] Hongxia Zhu,et al. Numerical analysis and experimental study on the microvibration of an aerostatic thrust bearing with a pocketed orifice-type restrictor , 2015 .
[29] Senthil Kumar,et al. Performance of inherently compensated flat pad aerostatic bearings subject to dynamic perturbation forces , 2012 .