Damage behavior of SnAgCu/Cu solder joints subjected to thermomechanical cycling

Abstract Thermomechanical fatigue damage is a progressive process of material degradation. The objective of this study was to investigate the damage behavior of SnAgCu/Cu solder joints under thermomechanical cycling. A damage model was proposed based on continuum damage mechanics (CDM). Based upon an analysis of displacements for flip-chip solder joints subjected to thermal cycling, a special bimetallic loading frame with single-solder joint samples was designed to simulate the service conditions of actual joints in electronic packages. The assembly, which allowed for strain measurements of an individual solder joint during temperature cycling, was used to investigate the impact of stress–strain cycling on the damage behavior of SnAgCu/Cu solder joints. The characteristic parameters of the damage model were determined through thermomechanical cycling and strain measurement tests. The damage variable D  = 1 −  R 0 / R was selected, and values for it were obtained using a four-probe method for the single-solder joint samples every dozen cycles during thermomechanical cycling tests to verify the model. The results showed that the predicted damage was in good agreement with the experimental results. The damage evolution law proposed here is a function of inelastic strain, and the results showed that the damage rate of SnAgCu/Cu solder joints increased as the range of the applied strain increased. In addition, the microstructure evolution of the solder joints was analyzed using scanning electron microscopy, which provided the microscopic explanation for the damage evolution law of SnAgCu/Cu solder joints.

[1]  Lahouari Benabou,et al.  A thermo-mechanical cohesive zone model for solder joint lifetime prediction , 2013 .

[2]  Cemal Basaran,et al.  Electromigration damage mechanics of lead-free solder joints under pulsed DC: A computational model , 2013 .

[3]  Tiejun Wang,et al.  A continuous low cycle fatigue damage model and its application in engineering materials , 1997 .

[4]  M. Geers,et al.  Thermomechanical fatigue damage evolution in SAC solder joints , 2007 .

[5]  B. Weiss,et al.  Constitutive modeling of pressure dependent plasticity and fracture in solder joints , 2012 .

[6]  Yu-Lin Shen,et al.  Modeling of Solder Fatigue Failure due to Ductile Damage , 2010 .

[7]  F. X. Che,et al.  Fatigue Reliability Analysis of Sn–Ag–Cu Solder Joints Subject to Thermal Cycling , 2013, IEEE Transactions on Device and Materials Reliability.

[8]  Mingyu Li,et al.  Dependence of recrystallization on grain morphology of Sn-based solder interconnects under thermomechanical stress , 2012 .

[9]  J. Wilde,et al.  Applying Anand Model to Represent the Viscoplastic Deformation Behavior of Solder Alloys , 2001 .

[10]  Qingda Yang,et al.  A cohesive zone model for low cycle fatigue life prediction of solder joints , 2004 .

[11]  Qingke Zhang,et al.  Fracture mechanism and strength-influencing factors of Cu/Sn-4Ag solder joints aged for different times , 2009 .

[12]  B. A. Fiedler,et al.  Monitoring Fatigue Cracking in Interconnects in a Ball Grid Array by Measuring Electrical Resistance , 2012 .

[13]  F. Che,et al.  Characterization of IMC layer and its effect on thermomechanical fatigue life of Sn–3.8Ag–0.7Cu solder joints , 2012 .

[14]  Yuichi Otsuka,et al.  Creep–Fatigue Crack Growth Behavior of Pb-Containing and Pb-Free Solders at Room and Elevated Temperatures , 2012, Journal of Electronic Materials.

[15]  S. Wiese,et al.  Characterization of Lead-Free Solders in Flip Chip Joints , 2003 .

[16]  J. Lemaître.  How to use damage mechanics , 1984 .

[17]  Ganesh Subbarayan,et al.  Maximum-Entropy Principle for Modeling Damage and Fracture in Solder Joints , 2012, Journal of Electronic Materials.

[18]  B. Sammakia,et al.  Simulations of Damage, Crack Initiation, and Propagation in Interlayer Dielectric Structures: Understanding Assembly-Induced Fracture in Dies , 2012, IEEE Transactions on Device and Materials Reliability.

[19]  A. Dasgupta,et al.  A meso-scale damage evolution model for cyclic fatigue of viscoplastic materials , 2009 .

[20]  B. Li,et al.  Size and constraint effects on interfacial fracture behavior of microscale solder interconnects , 2013, Microelectron. Reliab..

[21]  Owen Thomas,et al.  Novel Testing Instrument for Lead-Free Solder Characterization , 2011, IEEE Transactions on Instrumentation and Measurement.

[22]  G. Gray,et al.  The constitutive response of three solder materials , 2012 .

[23]  Jean Lemaitre,et al.  Application of Damage Concepts to Predict Creep-Fatigue Failures , 1979 .

[24]  Wenjie Wang,et al.  Quantification of creep strain in small lead-free solder joints with the in-situ micro electronic-resistance measurement , 2007, 2007 International Conference on Thermal, Mechanical and Multi-Physics Simulation Experiments in Microelectronics and Micro-Systems. EuroSime 2007.