Experimental and numerical study on seismic sliding mechanism of laminated-rubber bearings

Abstract Typical laminated rubber bearings are widely used in small to medium-span highway bridges in China. These bearings are economical, and are proved to perform well at service-level conditions. However, damage investigation after the 2008 Wenchuan earthquake revealed that sliding between the laminated rubber bearing and the bridge girder was a common phenomenon, which could actually act as fuses and protect the substructures from severe damage. Thus no damage or only minor damage of substructures was reported in the Wenchuan earthquake for those bridges with bearing sliding. In this paper, an experimental program was carried out to investigate the sliding behavior of laminated rubber bearings with typical configurations in China. The bearing was placed directly on a steel plate representing the embedded steel plate at the bottom of bridge girders, to create an elastomer-steel sliding surface. Experiment results showed that the behavior of bearings before obvious sliding could be approximated as a linear elastic response, with an effective shear modulus in the range of 610–1100 kPa. The sliding coefficients of friction were observed to be inversely related to the normal force, and positively related to the sliding velocity. An analytical model considering the sliding response of laminated-rubber bearings on steel plates was developed and calibrated. Numerical simulations were also conducted to compare the proposed model to the model with typical Coulomb’s friction. Results from the numerical simulations indicated that the vertical earthquake caused differences of bearing displacement response between these two models. And this difference would be more significant as the intensity of vertical earthquake increased.

[1]  A H Muhr,et al.  Effect of scragging on parameters in viscoplastic model for filled rubber , 2011 .

[2]  Michel Bruneau,et al.  Analytical Response and Design of Buildings with Metallic Structural Fuses. I , 2009 .

[3]  James Michael LaFave,et al.  Evaluation of quasi-isolated seismic bridge behavior using nonlinear bearing models , 2013 .

[4]  Jianfeng Zhao,et al.  Seismic damage of highway bridges during the 2008 Wenchuan earthquake , 2009 .

[5]  Michel Bruneau,et al.  Experimental Response of Buildings Designed with Metallic Structural Fuses. II , 2009 .

[6]  Andrei M. Reinhorn,et al.  Teflon Bearings in Base Isolation I: Testing , 1990 .

[7]  George C. Lee,et al.  Quasi‐Static and Dynamic Sliding Characteristics of Teflon—Stainless Steel Interfaces , 1990 .

[8]  Jianzhong Li,et al.  Damage investigation of girder bridges under the Wenchuan earthquake and corresponding seismic design recommendations , 2008 .

[9]  James Michael LaFave,et al.  Seismic analysis incorporating detailed structure–abutment–foundation interaction for quasi-isolated highway bridges , 2017 .

[10]  Michel Bruneau,et al.  Buckling restrained braces as structural fuses for the seismic retrofit of reinforced concrete bridge bents , 2011 .

[11]  Kuang-Yen Liu,et al.  Parametric study on performance of bridge retrofitted by unseating prevention devices , 2006 .

[12]  Daniel H. Tobias,et al.  Overview of Earthquake Resisting System Design and Retrofit Strategy for Bridges in Illinois , 2008 .

[13]  Hamid Ahmadi,et al.  A parametric study on the axial behaviour of elastomeric isolators in multi-span bridges subjected to horizontal seismic excitations , 2016, Bulletin of Earthquake Engineering.

[14]  Jianzhong Li,et al.  Shake-table tests and numerical simulation of an innovative isolation system for highway bridges , 2016 .

[15]  James Michael LaFave,et al.  Seismic performance of highway bridges with fusing bearing components for quasi‐isolation , 2013 .

[16]  Jianzhong Li,et al.  Seismic Performance of Highway Bridges with Different Transverse Unseating-Prevention Devices , 2016 .

[17]  Kuang-Yen Liu,et al.  Seismic performance of bridges with rubber bearings: lessons learnt from the 1999 Chi-Chi Taiwan earthquake , 2011 .

[18]  James Michael LaFave,et al.  Shear and friction response of nonseismic laminated elastomeric bridge bearings subject to seismic demands , 2013 .