Three-Dimensional Modeling and Experimental Study of a High Temperature PBI-Based PEM Fuel Cell

This paper investigates the performance of a high temperature proton exchange membrane (PEM) fuel cell. Both experimental work and numerical simulation are conducted. The high temperature proton exchange membrane is based on polybenzimidazole (PBI) doped with phosphoric acid. A single cell with triple serpentine flow channels was operated at steady state at various levels of temperature, pressure, and air stoichiometry. A three-dimensional model was used to simulate the cell performance, and polarization curves were used to validate the experimental values. The theoretical model accurately predicts the experimental results. A sound knowledge of the impact of various variables at various levels of the cell operation is necessary for unraveling the parametric influence and can prove extremely useful for optimizing the cell operation.

[1]  G. Jung,et al.  Preparation of a low proton resistance PBI/PTFE composite membrane , 2007 .

[2]  Norman Munroe,et al.  Three dimensional modeling of high temperature PEM fuel cells , 2006 .

[3]  Yanghua Tang,et al.  Polybenzimidazole-membrane-based PEM fuel cell in the temperature range of 120–200 °C , 2007 .

[4]  Xuan Cheng,et al.  Hydrogen crossover in high-temperature PEM fuel cells , 2007 .

[5]  Norman Munroe,et al.  Mathematical model of a PEMFC using a PBI membrane , 2006 .

[6]  Thomas J. Schmidt,et al.  Properties of high-temperature PEFC Celtec®-P 1000 MEAs in start/stop operation mode , 2008 .

[7]  Ronghuan He,et al.  The CO Poisoning Effect in PEMFCs Operational at Temperatures up to 200°C , 2003 .

[8]  Xuan Cheng,et al.  PEM fuel cells operated at 0% relative humidity in the temperature range of 23–120 °C , 2007 .

[9]  A. Abdel-azim.  Fundamentals of Heat and Mass Transfer , 2011 .

[10]  Edward L Cussler,et al.  Diffusion: Mass Transfer in Fluid Systems , 1984 .

[11]  Pablo Cañizares,et al.  Improved polybenzimidazole films for H3PO4-doped PBI-based high temperature PEMFC , 2007 .

[12]  Shimshon Gottesfeld,et al.  Electro‐osmotic Drag of Water in Ionomeric Membranes New Measurements Employing a Direct Methanol Fuel Cell , 1997 .

[13]  Zhenyu Liu,et al.  Study of the oxygen reduction reaction (ORR) at Pt interfaced with phosphoric acid doped polybenzimidazole at elevated temperature and low relative humidity , 2006 .

[14]  O. Savadogo.  Emerging membranes for electrochemical systems: Part II. High temperature composite membranes for polymer electrolyte fuel cell (PEFC) applications☆ , 2004 .

[15]  Jesse S. Wainright,et al.  Conductivity of PBI Membranes for High-Temperature Polymer Electrolyte Fuel Cells , 2004 .

[16]  Jesse S. Wainright,et al.  A H2O2 fuel cell using acid doped polybenzimidazole as polymer electrolyte , 1996 .

[17]  Jingwei Hu,et al.  Studies of performance degradation of a high temperature PEMFC based on H3PO4-doped PBI , 2006 .

[18]  R. Savinell,et al.  Electro‐osmotic Drag Coefficient of Water and Methanol in Polymer Electrolytes at Elevated Temperatures , 1996 .

[19]  J. Bear.  Modelling Transport Phenomena in Porous Media , 1991 .