Buffer layer formation in organic photovoltaic cells by self-organization of poly(dimethylsiloxane)s

Abstract A surface-segregated thin layer of poly(dimethylsiloxane)-block-poly(methylmethacrylate) (PDMS-b-PMMA) formed by self-organization during spin-coating was utilized as an interfacial buffer layer in organic photovoltaic cells. X-ray photoelectron spectroscopy revealed that PDMS-b-PMMA mixed into the coating solution spontaneously accumulated at the surface of the active layer due to the low surface energy of PDMS. The introduction of the PDMS-b-PMMA layer in bulk-heterojunction cells of poly(3-hexylthiophene):[6,6]-phenyl C61-butyric acid methyl ester resulted in an improvement of the power conversion efficiency (PCE) of the cells from 3.05% to 3.56% on average. The highest PCE of 3.86% was achieved with 0.4 mg ml−1 of PDMS-b-PMMA. These results indicate that the PDMS-b-PMMA layer formed by self-organization provides a facile and versatile approach to improve the photovoltaic performance, possibly by suppressing charge carrier recombination at the organic/metal interface.

[1]  Negative bias temperature instability and Fowler-Nordheim injection in silicon oxynitride insulators , 2007 .

[2]  S. T. Lee,et al.  Enhanced brightness and efficiency in organic electroluminescent devices using SiO2 buffer layers , 1999 .

[3]  Masahiro Hiramoto,et al.  Organic solar cells protected by very thick naphthalene tetracarboxylic anhydride films , 2004 .

[4]  Mm Martijn Wienk,et al.  The use of ZnO as optical spacer in polymer solar cells: Theoretical and experimental study , 2007 .

[5]  Yongfang Li,et al.  Performance improvement of polymer solar cells by using a solution processible titanium chelate as cathode buffer layer , 2007 .

[6]  M. Green,et al.  678-mV open-circuit voltage silicon solar cells , 1981 .

[7]  O. Park,et al.  Low vacuum process for polymer solar cells: Effect of TiOx interlayer , 2008 .

[8]  Kazuhito Hashimoto,et al.  Self‐Organized Buffer Layers in Organic Solar Cells , 2008 .

[9]  C. Brabec,et al.  Effect of LiF/metal electrodes on the performance of plastic solar cells , 2002 .

[10]  Olle Inganäs,et al.  Enhancing the Photovoltage of Polymer Solar Cells by Using a Modified Cathode , 2007 .

[11]  T. Marks,et al.  High-efficiency hole extraction/electron-blocking layer to replace poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) in bulk-heterojunction polymer solar cells , 2008 .

[12]  M.A. Green,et al.  High-efficiency silicon solar cells , 1984, IEEE Transactions on Electron Devices.

[13]  Vishal Shrotriya,et al.  Transition metal oxides as the buffer layer for polymer photovoltaic cells , 2006 .

[14]  M. Powalla,et al.  Comparative study of the influence of LiF, NaF, and KF on the performance of polymer bulk heterojunction solar cells , 2007 .

[15]  Alex K.-Y. Jen,et al.  Self-assembled monolayer modified ZnO/metal bilayer cathodes for polymer/fullerene bulk-heterojunction solar cells , 2008 .

[16]  Xiong Gong,et al.  New Architecture for High‐Efficiency Polymer Photovoltaic Cells Using Solution‐Based Titanium Oxide as an Optical Spacer , 2006 .