Focused laser lithographic system for efficient and cross-scale fabrication of large-area and 3D micro-patterns

Abstract A novel focused laser lithographic system with a low-power ultraviolet laser, a high-speed galvanometer scanner and a customized F-theta lens was constructed and demonstrated for cross-scale, high-efficiency and low-cost fabrication of large-area micro-patterns. In this system, a high-speed galvanometer scanner was used for the first time to greatly improve lithographic efficiency. The optical path was optimized and studied in detail, and the distortions caused by the scanners and F-theta lens were explained with mathematical expressions. Then, a method of correction chart was employed to further reduce the distortion and stitching error. The effect of laser parameters on linewidth of the fabricated micro-patterns was investigated and optimized. The significance sequence of these parameters was laser power, scan time, scan speed and defocus, and the optimal line width/space was below 10 µm. After the optimization, a 150 mm × 150 mm gridding with 9.8 µm linewidth and 90 µm line space was fabricated within 300 s, and the stitching error was less than 10%. To demonstrate the ability for arbitrary micro-patterns fabrication, a 150 mm × 120 mm HUST logo with the feature size of about 10 µm was fabricated within 40 s. Array circular holes with the feature size of below 10 µm were also obtained with a scan speed of 2000 mm/s. Using this system, cross-scale and large-area micro-patterns could be fabricated conveniently with high efficiency and less stitching error. With the assistance of z stage, the system can also realize three-dimension (3D) micro-fabrication.

[1]  Geoffroy Auvert.  Continuous-wave laser-assisted fabrication of microstructures in silicon microelectronics , 1994, Other Conferences.

[2]  T. Milster,et al.  Freeform diffractive structure writing through maskless lithography , 2014 .

[3]  R. Pethrick,et al.  Light emitting polymer blends and diffractive optical elements in high-speed direct laser writing of microstructures , 2008 .

[4]  Mangirdas Malinauskas,et al.  Fabrication of micro-tube arrays in photopolymer SZ2080 by using three different methods of a direct laser polymerization technique , 2012 .

[5]  B. Sopori,et al.  Focused laser lithographic system. , 1978, Applied optics.

[6]  Harry J. Levinson,et al.  Principles of Lithography , 2001 .

[7]  P. Abgrall,et al.  Lab-on-chip technologies: making a microfluidic network and coupling it into a complete microsystem—a review , 2007 .

[8]  Zhenwu Lu,et al.  Fabrication of large diffractive optical elements in thick film on a concave lens surface. , 2003, Optics express.

[9]  Xin Zhang,et al.  Building embedded microchannels using a single layered SU-8, and determining Young's modulus using a laser acoustic technique , 2004 .

[10]  Saulius Juodkazis,et al.  Three-Dimensional Structuring of Resists and Resins by Direct Laser Writing and Holographic Recording , 2007 .

[11]  Roger Fabian W. Pease,et al.  Lithography and Other Patterning Techniques for Future Electronics , 2008, Proceedings of the IEEE.

[12]  G. Lo,et al.  Low-loss silicon slot waveguides and couplers fabricated with optical lithography and atomic layer deposition. , 2011, Optics express.

[13]  Zhenwu Lu,et al.  Fabrication of a curved linear grating by using a laser direct writer system , 2006 .

[14]  M. Rothschild.  Projection optical lithography , 2005 .

[15]  Meng-Hua Yen,et al.  Crack-free direct-writing on glass using a low-power UV laser in the manufacture of a microfluidic chip , 2005 .

[16]  S. Bhave,et al.  Partial Gap Transduced MEMS Optoacoustic Oscillator Beyond Gigahertz , 2015, Journal of Microelectromechanical Systems.

[17]  J. Temmyo,et al.  Single cuprous oxide films synthesized by radical oxidation at low temperature for PV application. , 2013, Optics express.

[18]  A. Yalçinkaya,et al.  Polymer-MEMS-Based Optoelectronic Display , 2010, IEEE Transactions on Electron Devices.

[19]  Qiancheng Zhao,et al.  Sub-micron silicon nitride waveguide fabrication using conventional optical lithography. , 2015, Optics express.

[20]  G. Cirino,et al.  Two-dimensional diffraction grating fabricated by maskless lithography , 2014, 2014 29th Symposium on Microelectronics Technology and Devices (SBMicro).

[21]  G. Whitesides.  The origins and the future of microfluidics , 2006, Nature.