The effect of bark content on quality parameters of Scots pine (Pinus sylvestris L.) pellets

Abstract Increased use of pellets has resulted in a shortage of the traditional raw materials required for pellet making, including saw dust, shavings and cuttings from saw mills. Therefore, the pellets industry has started to look for alternative raw materials. Limited consumption of pulpwood from Scots pine ( Pinus sylvestris L.) in Norway has made it a potential raw material for the pellets industry. A study on how bark content affects the quality of pellets is reported in this paper. Pellets from pinewood containing zero, five, 10, 30 and 100 percent bark were produced, and their quality parameters were evaluated. Combustion tests were also performed on the produced pellets. Pellets made from pure bark had the best mechanical properties compared with pellets made of wood containing various concentrations of bark. The differences were not substantial and the durability for all chosen assortments was in the same quality class in the CEN standard. A positive effect off the amount of steam added was found. The bulk densities of the blend pellets were higher than those of pure wood and bark. The ash content increased with the amount of bark in the pellets. There were no problems with sintering when the bark content was low (five and 10 percent). For pure bark pellets some sintering was registered.

[1]  M. P. Levi,et al.  Effect of species and wood to bark ratio on pelleting of southern woods , 1984 .

[2]  A.F.B. van der Poel,et al.  Physical quality of pelleted animal feed. 2. contribution of processes and its conditions , 1997 .

[3]  Marcus Öhman,et al.  Effect of raw material composition in woody biomass pellets on combustion characteristics. , 2007 .

[4]  M. Hupa,et al.  Ash-forming elements in four Scandinavian wood species. Part 1: Summer harvest , 2005 .

[5]  Paul Geladi,et al.  High quality biofuel pellet production from pre-compacted low density raw materials. , 2008, Bioresource technology.

[6]  I. Obernberger,et al.  Chemical properties of solid biofuels¿significance and impact , 2006 .

[7]  Ingwald Obernberger,et al.  Determination of major and minor ash-forming elements in solid biofuels , 2006 .

[8]  M. Sjöström,et al.  Effects of raw material moisture content, densification pressure and temperature on some properties of Norway spruce pellets , 2005 .

[9]  M. Öhman,et al.  Slagging tendencies of wood pellet ash during combustion in residential pellet burners , 2004 .

[10]  Eija Alakangas,et al.  CEN technical specification for solid biofuels—Fuel specification and classes , 2006 .

[11]  Beatrice Coda,et al.  Slagging Behavior of Wood Ash under Entrained-Flow Gasification Conditions , 2007 .

[12]  I. Obernberger,et al.  Physical characterisation and chemical composition of densified biomass fuels with regard to their combustion behaviour , 2004 .

[13]  Maria E. Olsson.  Wheat straw and peat for fuel pellets - organic compounds from combustion , 2006 .

[14]  Dan Boström,et al.  Slagging characteristics during residential combustion of biomass pellets , 2008 .

[15]  P. D. Jensen,et al.  Comparative study of durability test methods for pellets and briquettes , 2006 .

[16]  M. Öhman,et al.  Reasons for slagging during stemwood pellet combustion and some measures for prevention , 2004 .

[17]  P. Lehtikangas.  Quality properties of pelletised sawdust, logging residues and bark , 2001 .

[18]  Juha Nurmi,et al.  Heating values of the above ground biomass of small-sized trees. , 1993 .

[19]  Johan Vinterbäck,et al.  Pellets 2002: the first world conference on pellets. , 2004 .

[20]  Magnus Ståhl,et al.  Industrial processes for biomass drying and their effects on the quality properties of wood pellets , 2004 .