Design and experiment study of a semi-active energy-regenerative suspension system

A new kind of semi-active energy-regenerative suspension system is proposed to recover suspension vibration energy, as well as to reduce the suspension cost and demands for the motor-rated capacity. The system consists of an energy-regenerative damper and a DC-DC converter-based energy-regenerative circuit. The energy-regenerative damper is composed of an electromagnetic linear motor and an adjustable shock absorber with three regulating levels. The linear motor just works as the generator to harvest the suspension vibration energy. The circuit can be used to improve the system's energy-regenerative performance and to continuously regulate the motor's electromagnetic damping force. Therefore, although the motor works as a generator and damps the isolation without an external power source, the motor damping force is controllable. The damping characteristics of the system are studied based on a two degrees of freedom vehicle vibration model. By further analyzing the circuit operation characteristics under different working modes, the double-loop controller is designed to track the desired damping force. The external-loop is a fuzzy controller that offers the desired equivalent damping. The inner-loop controller, on one hand, is used to generate the pulse number and the frequency to control the angle and the rotational speed of the step motor; on the other hand, the inner-loop is used to offer the duty cycle of the energy-regenerative circuit. Simulations and experiments are conducted to validate such a new suspension system. The results show that the semi-active energy-regenerative suspension can improve vehicle ride comfort with the controllable damping characteristics of the linear motor. Meanwhile, it also ensures energy regeneration.

[1]  Yoshihiro Suda,et al.  Modeling of Electromagnetic Damper for Automobile Suspension , 2007 .

[2]  S. Sankar,et al.  A New Concept in Semi-Active Vibration Isolation , 1987 .

[3]  Lei Zuo,et al.  MODELING OF AN ELECTROMAGNETIC VIBRATION ENERGY HARVESTER WITH MOTION MAGNIFICATION , 2011 .

[4]  R. B. Goldner,et al.  A Preliminary Study of Energy Recovery in Vehicles by Using Regenerative Magnetic Shock Absorbers , 2001 .

[5]  L. R. Miller.  Tuning passive, semi-active, and fully active suspension systems , 1988, Proceedings of the 27th IEEE Conference on Decision and Control.

[6]  Yoshihiro Suda,et al.  STUDY ON ELECTROMAGNETIC DAMPER FOR AUTOMOBILES WITH NONLINEAR DAMPING FORCE CHARACTERISTICS , 2004 .

[7]  Lei Zuo,et al.  Energy Harvesting, Ride Comfort, and Road Handling of Regenerative Vehicle Suspensions paper presents a comprehensive assessment of the power that is available for harvest- , 2013 .

[8]  Lei Zuo,et al.  Electromagnetic Energy-Harvesting Shock Absorbers: Design, Modeling, and Road Tests , 2013, IEEE Transactions on Vehicular Technology.

[9]  W. D. Jones,et al.  Easy ride: Bose Corp. uses speaker technology to give cars adaptive suspension , 2005 .

[10]  Ping Hsu.  Power recovery property of electrical active suspension systems , 1996, IECEC 96. Proceedings of the 31st Intersociety Energy Conversion Engineering Conference.

[11]  G. D. Marques,et al.  Permanent-magnets linear actuators applicability in automobile active suspensions , 2006, IEEE Transactions on Vehicular Technology.

[12]  Glenn R. Wendel,et al.  A Regenerative Active Suspension System , 1991 .

[13]  Tzuu-Hseng S. Li,et al.  Design of fuzzy controller for active suspension system , 1995 .

[14]  Hiroshi Matsuhisa,et al.  Semi-active vibration isolation system with variable stiffness and damping control , 2008 .

[15]  L. Zuo,et al.  Energy-harvesting shock absorber with a mechanical motion rectifier , 2013 .

[16]  Yoshihiro Suda,et al.  Self-powered active vibration control using a single electric actuator , 2003 .

[17]  Johannes J. H. Paulides,et al.  Efficiency of a Regenerative Direct-Drive Electromagnetic Active Suspension , 2010, IEEE Transactions on Vehicular Technology.

[18]  Kongde He,et al.  Semi-active Suspension of a Full-vehicle Model based on Double-loop Control , 2011 .

[19]  Douglas E. Ivers,et al.  Experimental Comparison of Passive, Semi-Active On/Off, and Semi-Active Continuous Suspensions , 1989 .

[20]  Haobin Jiang.  Performance Simulation and Testing of Two-levels-damping Adjustable Hydraulic Shock Absorber , 2010 .

[21]  Ali Davoudi,et al.  Numerical state-space average-value modeling of PWM DC-DC converters operating in DCM and CCM , 2006, IEEE Transactions on Power Electronics.

[22]  R. C. Redfield,et al.  The Variable Linear Transmission for Regenerative Damping in Vehicle Suspension Control , 1992, 1992 American Control Conference.

[23]  Y. Okada,et al.  Regenerative control of active vibration damper and suspension systems , 1996, Proceedings of 35th IEEE Conference on Decision and Control.

[24]  Robin C. Redfield.  The Variable Linear Transmission for Regenerative Damping in Vehicle Suspension Control , 1993 .

[25]  Bogdan Sapiński,et al.  Energy balance in self-powered MR damper-based vibration reduction system , 2011 .

[26]  Yoshihiro Suda,et al.  Combined Type Self-Powered Active Suspensions for Rubber-Tired Vehicles , 2003 .

[27]  Yan-Fei Liu,et al.  A Design Method for PI-like Fuzzy Logic Controllers for DC–DC Converter , 2007, IEEE Transactions on Industrial Electronics.

[28]  António Pedro Souto,et al.  Application of nanotechnology in antimicrobial finishing of biomedical textiles , 2014 .

[29]  O. Sename,et al.  Survey and performance evaluation on some automotive semi-active suspension control methods: A comparative study on a single-corner model , 2012, Annu. Rev. Control..

[30]  D. L. Margolis,et al.  Regenerative Systems for Vibration Control , 1997 .