Cure Cycle for Thick Glass/Epoxy Composite Laminates

Duringthe curingprocess of thick glass/epoxy composite laminates, substantial amounts of temperature lagand overshoot at the center of the laminates is usually experienced due to the large thickness and low thermal conductivity of the glass/epoxy composites, which require a long time for full and uniform consolidation. In this work, the temperature profiles of a 20mm thick unidirectional glass/epoxy laminate duringan autoclave vacuum bag process were measured and compared with the numerically calculated results. For the calculation of distributions of the temperature, degree of cure, resin pressure, exothermic heat and required time for full consolidation by three-dimensional finite element analyses, the effects of convective heat transfer coefficient and geometry of mold and bagging assembly on the temperature profiles were taken into consideration. Based on the numerical results, an optimized cure cycle with the coolingand reheatingsteps was developed by minimizingthe objective function to reduce the temperature overshoot in the composite. From the experimental and numerical results, it was found that the measured temperature profiles were in good agreement with the numerical ones, and conventional cure cycles recommended by prepregmanufacturers for thin laminates should be modified to prevent temperature overshoot and to obtain full consolidation.

[1]  George S. Springer,et al.  Heat of Reaction, Degree of Cure, and Viscosity of Hercules 3501-6 Resin , 1982 .

[2]  S. Yi,et al.  Effects of Thermo-Mechanical Properties of Composites on Viscosity, Temperature and Degree of Cure in Thick Thermosetting Composite Laminates during Curing Process , 1998 .

[3]  S. Peters.  Handbook of Composites , 1998 .

[4]  Timothy G. Gutowski,et al.  The Consolidation of Laminate Composites , 1987 .

[5]  Sunil C. Joshi,et al.  A numerical approach to the modeling of polymer curing in fibre-reinforced composites , 1999 .

[6]  Wen-Bin Young,et al.  Compacting pressure and cure cycle for processing of thick composite laminates , 1995 .

[7]  Peter R. Ciriscioli,et al.  Cure Kinetics and Viscosity of Fiberite 976 Resin , 1987 .

[8]  Scott R. White,et al.  Staged curing of composite materials , 1996 .

[9]  Model Laws for Curing of Thermosetting Composites , 1995 .

[10]  George S. Springer,et al.  Autoclave Curing — Comparisons of Model and Test Results , 1992 .

[11]  H. Kreft,et al.  Fiber reinforced composites for space systems , 1970 .

[12]  John W. Gillespie,et al.  Two-Dimensional Cure Simulation of Thick Thermosetting Composites , 1991 .

[13]  Sean McKee,et al.  Curing simulation of thermoset composites , 1999 .

[14]  Dai Gil Lee,et al.  Development of an Autoclave Cure Cycle with Cooling and Reheating Steps for Thick Thermoset Composite Laminates , 1997 .

[15]  P. Geil,et al.  Curing in Thick Composite Laminates: Experiment and Simulation , 1993 .

[16]  Gregory M. Glenn,et al.  Fiber-reinforced composites , 1988 .

[17]  A. Beris,et al.  Curing Behavior of Thick-Sectioned RTM Composites , 1998 .

[18]  George S. Springer,et al.  Thermal Conductivities of Unidirectional Materials , 1967 .

[19]  Gregory M. Martinez.  Fast cures for thick laminated organic matrix composites , 1991 .

[20]  D. Lee,et al.  On-line cure monitoring and viscosity measurement of carbon fiber epoxy composite materials , 1993 .

[21]  S. J. Wineman,et al.  Consolidation Experiments for Laminate Composites , 1987 .

[22]  L. Chiao,et al.  A Fundamental Approach to Resin Cure Kinetics , 1990 .

[23]  Wen-Bin Young,et al.  Consolidation and cure simulations for laminated composites , 1996 .

[24]  K. S. Jeong,et al.  Interlaminar Shear Behavior of Thick Carbon/Epoxy Composite Materials , 1999 .