Transverse flux machines with distributed windings for in-wheel applications

Transverse flux machine (TFM) useful for in-wheel motor applications is presented. This transverse flux permanent magnet motor is designed to achieve high torque-to-weight ratio and is suitable for direct-drive wheel applications. As in conventional TFM, the phases are located under each other, which will increase the axial length of the machine. The idea of this design is to reduce the axial length of TFM, by placing the windings around the stator and by shifting those from each other by electrically 120° or 90°, for three- or two-phase machine, respectively. Therefore, a remarkable reduction on the total axial length of the machine will be achieved while keeping the torque density high. This TFM is compared to another similar TFM, in which the three phases have been divided into two halves and placed opposite each other to ensure the mechanical balance and stability of the stator. The corresponding mechanical phase shifts between the phases have accordingly been taken into account. The motors are modelled in finite-element method (FEM) program, Flux3D, and designed to meet the specifications of an optimisation scheme, subject to certain constraints, such as construction dimensions, electric and magnetic loading. Based on this comparison study, many recommendations have been suggested to achieve optimum results.

[1]  Jian Guo Zhu,et al.  Development of a PM transverse flux motor with soft magnetic composite core , 2006, IEEE Transactions on Energy Conversion.

[2]  F. Crescimbini,et al.  Compact wheel direct drive for EVs , 1996 .

[3]  Li Weili,et al.  Optimal design and finite element analysis of switched reluctance motor for electric vehicles , 2008, 2008 IEEE Vehicle Power and Propulsion Conference.

[4]  Barrie Mecrow,et al.  Design of an in-wheel motor for a solar-powered electric vehicle , 1997 .

[5]  B. Asaei,et al.  Comparative study of using different electric motors in the electric vehicles , 2008, 2008 18th International Conference on Electrical Machines.

[6]  H. Bulent Ertan,et al.  A comparison of torque capabilities of axial flux and radial flux type of brushless DC (BLDC) drives for wide speed range applications , 1999 .

[7]  Jianguo Zhu,et al.  Design and analysis of a transverse flux machine with soft magnetic composite core , 2003, Sixth International Conference on Electrical Machines and Systems, 2003. ICEMS 2003..

[8]  A. Tenconi,et al.  Axial flux machines drives: a new viable solution for electric cars , 1996, Proceedings of the 1996 IEEE IECON. 22nd International Conference on Industrial Electronics, Control, and Instrumentation.

[9]  J. Bird,et al.  Calculating the Forces Created by an Electrodynamic Wheel Using a 2-D Steady-State Finite-Element Method , 2008, IEEE Transactions on Magnetics.

[10]  L. Chang,et al.  Comparison of AC drives for electric vehicles-a report on experts' opinion survey , 1994, IEEE Aerospace and Electronic Systems Magazine.

[11]  Thomas A. Lipo,et al.  A comparison of power density for axial flux machines based on general purpose sizing equations , 1999 .

[12]  Hans-Peter Nee,et al.  Design Steps towards a High Power Factor Transverse Flux Machine , 2001 .

[13]  Kaiyuan Lu.  Design Study for Controllable Electric Motor for Three Wheel Drive, In Wheel Mounting on Professional, Electric, Lawn Mower , 2004 .

[14]  Ezio Santini,et al.  Multi-stage axial-flux PM machine for wheel direct drive , 1995, IAS '95. Conference Record of the 1995 IEEE Industry Applications Conference Thirtieth IAS Annual Meeting.

[15]  Tadashi Ashikaga,et al.  Novel motors and controllers for high-performance electric vehicle with four in-wheel motors , 1997, IEEE Trans. Ind. Electron..

[16]  K. Ohyama,et al.  Design using Finite Element Analysis of Switched Reluctance Motor for Electric Vehicle , 2006, 2006 2nd International Conference on Information & Communication Technologies.