On the effect of process parameters on properties of AlSi10Mg parts produced by DMLS

Purpose – The aim of this research is to reach a deep understanding on the effect of the process parameters of Direct Metal Laser Sintering process (DMLS) on macroscopic properties (hardness and density) of AlSi10Mg parts and resulting microstructure. Design/methodology/approach – A full factorial design of experiment (DOE) was applied to determine the most significant process parameter influencing macroscopic properties of AlSi10Mg parts manufactured by DMLS process. The analysis aims to define the optimum process parameters and deduce the process window that provides better macroscopic properties of AlSi10Mg parts. Optical microscopy observations are carried out to link the microstructure to macroscopic properties. Findings – Macroscopic properties of DMLS parts are influenced by the change in process parameters. There is a close correlation between the geometry of scan tracks and macroscopic properties of AlSi10Mg parts manufactured by DMLS process. Originality/value – The knowledge of utilizing optimi...

[1]  L. Froyen,et al.  Binding Mechanisms in Selective Laser Sintering and Selective Laser Melting , 2004 .

[2]  Eleonora Atzeni,et al.  Economics of additive manufacturing for end-usable metal parts , 2012 .

[3]  A. Spierings,et al.  Comparison of density measurement techniques for additive manufactured metallic parts , 2011 .

[4]  Di Wang,et al.  Parametric optimization of selective laser melting for forming Ti6Al4V samples by Taguchi method , 2013 .

[5]  F. Klocke,et al.  Consolidation phenomena in laser and powder-bed based layered manufacturing , 2007 .

[6]  T. Childs,et al.  Layer Formation Studies in Selective Laser Melting of Steel Powders , 2006 .

[7]  Hsin-Te Liao,et al.  Optimization on selective laser sintering of metallic powder via design of experiments method , 2007 .

[8]  Jean-Pierre Kruth,et al.  Microstructure and mechanical properties of maraging steel 300 after Selective Laser Melting , 2010 .

[9]  Christopher J. Sutcliffe,et al.  Selective laser melting of aluminium components , 2011 .

[10]  Jean-Pierre Kruth,et al.  Microstructure and mechanical properties of Selective Laser Melted 18Ni-300 steel , 2011 .

[11]  Y. Song,et al.  Experimental Study of the Basic Process Mechanism for Direct Selective Laser Sintering of Low-Melting Metallic Powder , 1997 .

[12]  J. Kruth,et al.  Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder , 2013 .

[13]  F. Calignano,et al.  Influence of process parameters on surface roughness of aluminum parts produced by DMLS , 2012, The International Journal of Advanced Manufacturing Technology.

[14]  Eleonora Atzeni,et al.  From Powders to Dense Metal Parts: Characterization of a Commercial AlSiMg Alloy Processed through Direct Metal Laser Sintering , 2013, Materials.

[15]  Igor Drstvenšek,et al.  Speed and accuracy evaluation of additive manufacturing machines , 2011 .

[16]  Gideon Levy,et al.  Designing material properties locally with additive manufacturing technology SLM , 2012 .

[17]  J. Kruth,et al.  Selective laser melting of biocompatible metals for rapid manufacturing of medical parts , 2006 .

[18]  Sanjay Kumar,et al.  An experimental design approach to selective laser sintering of low carbon steel , 2003 .

[19]  E. Brandl,et al.  Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior , 2012 .

[20]  Kenneth W. Dalgarno,et al.  Densification mechanism and microstructural evolution in selective laser sintering of Al-12Si powders , 2011 .

[21]  E. O. Olakanmi,et al.  Laser sintering of blended Al‐Si powders , 2012 .

[22]  I. Yadroitsava,et al.  Factor analysis of selective laser melting process parameters and geometrical characteristics of synthesized single tracks , 2012 .

[23]  Eugen Cicala,et al.  Experimental design approach to optimize selective laser melting of martensitic 17‐4 PH powder: part I – single laser tracks and first layer , 2012 .

[24]  Joaquim Ciurana,et al.  Influence of process parameters on part quality and mechanical properties for DMLS and SLM with iron-based materials , 2012 .

[25]  Yusheng Shi,et al.  316L Stainless Steel with Gradient Porosity Fabricated by Selective Laser Melting , 2010 .