Deformation and failure behaviour of Ti-6Al-4V lattice structures manufactured by selective laser melting (SLM)

Selective laser melting (SLM) enables the manufacture of lattice structures with highly engineered mechanical properties that are optimised for the associated design requirements. Such lattice structures offer high specific strength and stiffness characteristics allowing design freedom beyond the capacity of solid materials. However, to apply lattices as space filling structural elements, it is necessary to quantify their mechanical properties such as compressive strength and stiffness under varying geometric conditions. This work provides an experimental investigation of the manufacturability of SLM Ti-6Al-4V lattice struts of varying diameter and inclination. From this investigation, lattice structures are manufactured for varying cell topology, cell size, number of unit cells and associated boundary conditions. The deformation and failure behaviour of these lattices is theoretically predicted and experimentally validated. The convergence of mechanical properties with increasing number of unit cells, as well as the effect of lattice topology on mechanical behaviour and observed failures mode are reported.

[1]  S. Sun,et al.  The Effect of Manufacturing Defects on the Fatigue Behaviour of Ti-6Al-4V Specimens Fabricated Using Selective Laser Melting , 2014 .

[2]  Ola L. A. Harrysson,et al.  Properties of Ti–6Al–4V non-stochastic lattice structures fabricated via electron beam melting , 2008 .

[3]  Aleksandar Subic,et al.  Feasible Build Orientations for Self-Supporting Fused Deposition Manufacture: A Novel Approach to Space-Filling Tesselated Geometries , 2013 .

[4]  Claus Emmelmann,et al.  Rapid manufacturing of lattice structures with selective laser melting , 2006, SPIE LASE.

[5]  Jan Wieding,et al.  Numerical optimization of open-porous bone scaffold structures to match the elastic properties of human cortical bone. , 2014, Journal of the mechanical behavior of biomedical materials.

[6]  Martin Leary,et al.  High-Value SLM Aerospace Components: From Design to Manufacture , 2013 .

[7]  M. Elahinia,et al.  Manufacturing and processing of NiTi implants: A review , 2012 .

[8]  Kwan H. Lee,et al.  Determination of the optimal build direction for different rapid prototyping processes using multi-criterion decision making , 2006 .

[9]  S. McKown,et al.  Drop weight impact behaviour of sandwich panels with metallic micro lattice cores , 2013 .

[10]  Gi-Jung Nam,et al.  A new laser bonding method of anisotropic conductive films in flat panel display and in semiconductor packaging , 2006, SPIE LASE.

[11]  Martin Leary,et al.  Optimal topology for additive manufacture: A method for enabling additive manufacture of support-free optimal structures , 2014 .

[12]  Wai-Fah Chen,et al.  Principles of structural design , 2005 .

[13]  L. Froyen,et al.  Selective laser melting of iron-based powder , 2004 .

[14]  Flaviana Calignano,et al.  Design optimization of supports for overhanging structures in aluminum and titanium alloys by selective laser melting , 2014 .

[15]  M. Ashby,et al.  Cellular solids: Structure & properties , 1988 .

[16]  Hans Jürgen Maier,et al.  Additively manufactured cellular structures: Impact of microstructure and local strains on the monotonic and cyclic behavior under uniaxial and bending load , 2013 .

[17]  Guido A.O. Adam,et al.  Design for Additive Manufacturing—Element transitions and aggregated structures , 2014 .

[18]  Jean L. Cornillot,et al.  Annual Book of ASTM Standards , 2016 .

[19]  Daniel Thomas.  The development of design rules for selective laser melting , 2009 .

[20]  Ahmed Hussein,et al.  Evaluations of cellular lattice structures manufactured using selective laser melting , 2012 .

[21]  Michael F. Zaeh,et al.  Investigations on Manufacturability and Process Reliability of Selective Laser Melting , 2013 .

[22]  Igor Smurov,et al.  Surface Morphology in Selective Laser Melting of Metal Powders , 2011 .

[23]  Andreas Öchsner,et al.  Cellular and Porous Materials in Structures and Processes , 2010 .

[24]  M. Ashby,et al.  Metal Foams: A Design Guide , 2000 .

[25]  Antonio Domenico Ludovico,et al.  Capabilities and Performances of the Selective Laser Melting Process , 2010 .

[26]  M. Ashby.  The properties of foams and lattices , 2006, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[27]  Richard M. Everson,et al.  A new approach to the design and optimisation of support structures in additive manufacturing , 2013 .

[28]  L. Froyen,et al.  Fundamentals of Selective Laser Melting of alloyed steel powders , 2006 .

[29]  Wesley J. Cantwell,et al.  The Mechanical Properties of Sandwich Structures Based on Metal Lattice Architectures , 2010 .

[30]  Jouke Verlinden,et al.  Optimal Design for Additive Manufacturing: Opportunities and Challenges , 2011 .

[31]  M. Ashby,et al.  FOAM TOPOLOGY BENDING VERSUS STRETCHING DOMINATED ARCHITECTURES , 2001 .

[32]  Yongqiang Yang,et al.  Research on the fabricating quality optimization of the overhanging surface in SLM process , 2013 .

[33]  B. Baufeld,et al.  Additive manufacturing of Ti–6Al–4V components by shaped metal deposition: Microstructure and mechanical properties , 2010 .

[34]  Paolo Colombo,et al.  Cellular Ceramics: Structure, Manufacturing, Properties and Applications , 2005 .