Characterizing heat transfer within a commercial-grade tubular solid oxide fuel cell for enhanced thermal management

A thermal transport model has been developed for analyzing heat transfer and improving thermal management within tubular solid oxide fuel cells (TSOFCs). The model was constructed via a proven electrochemical model and well-established heat transfer correlations. Its predictions compare favorably with other published data. Air temperatures consistently approach that of the fuel cell. This is primarily due to the high operating temperature of the cell (1000°C), the moderate magnitudes of radiation and airflow, and cell geometry. The required inlet air temperature (for thermally steady-state operation) has linear dependence on operating voltage and fuel utilization. Inlet air temperature has an inverse proportionality with respect to air stoichiometric number (i.e., inverse equivalence ratio). The current standard for airflow within TSOFCs was found to be excessive in consideration of the regenerative preheat effect within the supply pipes that feed air to the cell. Thermal management of simple TSOFC systems could be enhanced if commonly used air stoichiometric numbers were decreased.

[1]  A. J. Appleby,et al.  Characteristics of Fuel Cell Systems , 1993 .

[2]  A. Hagiwara.  FUEL CELL SYSTEMS , 2022 .

[3]  N. Bessette,et al.  A Mathematical Model of a Solid Oxide Fuel Cell , 1995 .

[4]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[5]  N. Giordano,et al.  Thermodynamic analysis of methane fueled solid oxide fuel cell system , 1992 .

[6]  Subhash C. Singhal,et al.  Proceedings of the Third International Symposium on Solid Oxide Fuel Cells , 1993 .

[7]  Andy Horsewell,et al.  Microstructural and microchemical characterization of the interface between La0.85Sr0.15MnO3 and Y2O3-stabilized ZrO2 , 1994 .

[8]  U. Merten,et al.  Electrical Resistivity of Stabilized Zirconia at Elevated Temperatures , 1963 .

[9]  Comas Lamar Haynes.  Simulation of tubular solid oxide fuel cell behavior for integration into gas turbine cycles , 1999 .

[10]  Comas Haynes,et al.  ‘Design for power’ of a commercial grade tubular solid oxide fuel cell , 2000 .

[11]  W. Rohsenow,et al.  Handbook of Heat Transfer Fundamentals , 1985 .

[12]  M. Ippommatsu,et al.  Evaluation of a New Solid Oxide Fuel Cell System by Non‐isothermal Modeling , 1992 .

[13]  Supramaniam Srinivasan,et al.  Research, Development, and Demonstration of Solid Oxide Fuel Cell Systems , 1993 .

[14]  高橋 武彦,et al.  Science and technology of ceramic fuel cells , 1995 .

[15]  Raymond Anthony George,et al.  PERFORMANCE AND RELIABILITY OF WESTINGHOUSE'S AIR ELECTRODE SUPPORTED SOLID OXIDE FUEL CELL AT ATMOSPHERIC AND ELEVATED PRESSURES , 1996 .

[16]  K. Kanamura.  Temperature Distribution in Tubular Solid Oxide Fuel Cell , 1989 .

[17]  Raymond Anthony George,et al.  Reducing the manufacturing cost of tubular solid oxide fuel cell technology , 1998 .

[18]  D.H. Archer,et al.  Power generation by combined fuel cell and gas turbine systems , 1996, IECEC 96. Proceedings of the 31st Intersociety Energy Conversion Engineering Conference.

[19]  J. C. Amphlett,et al.  A model predicting transient responses of proton exchange membrane fuel cells , 1996 .

[20]  J. V. Roosmalen.  Chemical reactivity and interdiffusion of (La, Sr)MnO3 and (Zr, Y)O2, solid oxide fuel cell cathode and electrolyte materials , 1992 .

[21]  C. C. Chen,et al.  Synthesis and Characterization of ( CeO2 ) 0.8 ( SmO1.5 ) 0.2 Thin Films from Polymeric Precursors , 1993 .