Relationships between alveolar size and fibre distribution in a mammalian lung alveolar duct model.

A finite element model, comprising an assemblage of tetrakaidecahedra or truncated octahedra, is used to represent an alveolar duct unit. The dimensions of the elastin and collagen fibre bundles, and the surface tension properties of the air-liquid interfaces, are based on available published data. Changes to the computed static pressure-volume behavior with variation in alveolar dimensions and fibre volume densities are characterized using distensibility indices (K). The air-filled lung distensibility (Ka) decreased with a reduction in the alveolar airspace length dimensions and increased with a reduction of total fibre volume density. The saline-filled lung distensibility (Ks) remained constant with alveolar dimensions and increased with decreasing total fibre volume density. The degree of geometric anisotropy between the duct lumen and alveoli was computed over pressure-volume cycles. To preserve broadly isotropic behavior, parenchyma with smaller alveolar airspace length dimensions required higher concentrations of fibres located in the duct and less in the septa in comparison with parenchyma of larger airspace dimensions.

[1]  J. Butler,et al.  Light scattering by lungs correlates with stereological measurements. , 1985, Journal of applied physiology.

[2]  J. Butler,et al.  Geometric hysteresis in pulmonary surface-to-volume ratio during tidal breathing. , 1993, Journal of applied physiology.

[3]  R C Schroter,et al.  The mechanical behavior of a mammalian lung alveolar duct model. , 1995, Journal of biomechanical engineering.

[4]  R. Schroter.  Quantitative comparisons of mammalian lung pressure volume curves. , 1980, Respiration physiology.

[5]  Comparison of single breath carbon monoxide diffusing capacity and pressure-volume curves in detecting emphysema. , 1990, The American review of respiratory disease.

[6]  R. Schroter,et al.  Transpulmonary pressure gradient and ventilation distribution in excised lungs. , 1973, Respiration physiology.

[7]  S. Schürch,et al.  A captive bubble method reproduces the in situ behavior of lung surfactant monolayers. , 1989, Journal of applied physiology.

[8]  Cavity supermodes for gain‐saturated diode laser arrays , 1985 .

[9]  J. Bates,et al.  Exponential fitting of pressure-volume curves: confidence limits and sensitivity to noise. , 1990, Journal of applied physiology.

[10]  Y C Fung,et al.  Collagen and elastin fibers in human pulmonary alveolar walls. , 1988, Journal of applied physiology.

[11]  S. Schürch,et al.  Relations among alveolar surface tension, surface area, volume, and recoil pressure. , 1987, Journal of applied physiology.

[12]  J. Crapo,et al.  Alveolar septal structure in different species. , 1994, Journal of applied physiology.

[13]  Parenchymal mechanics at the alveolar level. , 1979 .

[14]  G. Cavagna,et al.  Alveolar resistance to atelectasis. , 1967, Journal of applied physiology.

[15]  F. Hoppin,et al.  Distribution of elastin and collagen in canine lung alveolar parenchyma. , 1989, Journal of applied physiology.

[16]  R. Skalak,et al.  A mathematical model of lung parenchyma. , 1980, Journal of biomechanical engineering.

[17]  W. Thurlbeck,et al.  Assessment of lung parenchymal destruction by using routine histologic tissue sections. , 1989, The American review of respiratory disease.

[18]  F. L. Matthews,et al.  Analysis of elastic and surface tension effects in the lung alveolus using finite element methods. , 1986, Journal of biomechanics.

[19]  H J Colebatch,et al.  Use of an exponential function for elastic recoil. , 1979, Journal of applied physiology: respiratory, environmental and exercise physiology.

[20]  G. Snider,et al.  In vitro effects of elastase and collagenase on mechanical properties of hamster lungs. , 1976, Chest.

[21]  J. Crapo,et al.  Three-dimensional reconstruction of alveoli in the rat lung for pressure-volume relationships. , 1987, Journal of applied physiology.

[22]  P. Haber,et al.  Alveolar size as a determinant of pulmonary distensibility in mammalian lungs. , 1983, Journal of applied physiology: respiratory, environmental and exercise physiology.

[23]  F. L. Matthews,et al.  Finite element analysis of lung alveolus. , 1980, Journal of biomechanics.

[24]  Y C Fung,et al.  A model of the lung structure and its validation. , 1988, Journal of applied physiology.

[25]  T A Wilson,et al.  A model for mechanical structure of the alveolar duct. , 1982, Journal of applied physiology: respiratory, environmental and exercise physiology.

[26]  J. Crapo,et al.  Spatial distribution of collagen and elastin fibers in the lungs. , 1990, Journal of applied physiology.

[27]  T. Wilson.  Surface tension-surface area curves calculated from pressure-volume loops. , 1982, Journal of applied physiology: respiratory, environmental and exercise physiology.

[28]  N. Pride,et al.  Exponential description of the static pressure-volume curve of normal and diseased lungs. , 2015, The American review of respiratory disease.

[29]  J. Butler,et al.  Lengths and topology of alveolar septal borders. , 1989, Journal of applied physiology.

[30]  Y. Fung,et al.  Collagen and elastin fibers in human pulmonary alveolar mouths and ducts. , 1987, Journal of applied physiology.

[31]  E. Kimmel,et al.  Surface tension and the dodecahedron model for lung elasticity. , 1990, Journal of biomechanical engineering.

[32]  R C Schroter,et al.  Bulk elastic properties of excised lungs and the effect of a transpulmonary pressure gradient. , 1973, Respiration physiology.

[33]  J. Clark,et al.  Elastic properties of single elastic fibers. , 1962, Journal of applied physiology.

[34]  C. Wiederhielm,et al.  Viscoelastic description of a collagenous tissue in simple elongation. , 1969, Journal of applied physiology.