Vrije Universiteit Brussel Modeling and design of an energy-efficient dual-motor actuation unit with a planetary differential and holding brakes

Abstract By connecting two drivetrains to a single load, a redundant degree of freedom is created. In this work, we investigate how the redundancy of such a system can be exploited in order to make it more energy efficient. The system under study consists of two drivetrains coupled to a planetary differential. Both drivetrains are composed of a geared DC motor and a holding brake. First, we derive an accurate semi-empirical model of this system and prove its validity on a test setup. Based on this model, which includes nonlinear friction terms, we analyze how the power flows and energy losses depend on the redundant degree of freedom. Furthermore, we discuss how the design of the actuator can be optimized for energy efficiency. This strategy is applied to a case study, where a 250 W geared DC motor is replaced by a more efficient dual-motor actuator. Experiments confirm that a dual-motor actuator succeeds in reducing the energy consumption at various loads and speeds. We also show that the results are very sensitive to friction and other speed- and load-dependent losses.

[1]  Bram Vanderborght,et al.  +SPEA introduction: Drastic actuator energy requirement reduction by symbiosis of parallel motors, springs and locking mechanisms , 2016, 2016 IEEE International Conference on Robotics and Automation (ICRA).

[2]  Frank Kreith,et al.  The CRC handbook of mechanical engineering , 1998 .

[3]  Tian-Hua Liu,et al.  An improved maximum efficiency control for dual-motor drive systems , 2014, 2014 6th International Conference on Information Technology and Electrical Engineering (ICITEE).

[4]  Carmel Majidi,et al.  A lightweight, low-power electroadhesive clutch and spring for exoskeleton actuation , 2016, 2016 IEEE International Conference on Robotics and Automation (ICRA).

[5]  H. Harry Asada,et al.  A practical optimal control approach for two-speed actuators , 2016, 2016 IEEE International Conference on Robotics and Automation (ICRA).

[6]  Herbert W. Muller,et al.  Epicyclic Gear Trains: Analysis, Synthesis and Applications , 1983 .

[7]  Bram Vanderborght,et al.  Energy Consumption of Geared DC Motors in Dynamic Applications: Comparing Modeling Approaches , 2016, IEEE Robotics and Automation Letters.

[8]  Jae-Bok Song,et al.  A Serial-Type Dual Actuator Unit With Planetary Gear Train: Basic Design and Applications , 2010, IEEE/ASME Transactions on Mechatronics.

[9]  Allan Joshua Veale,et al.  Towards compliant and wearable robotic orthoses: A review of current and emerging actuator technologies. , 2016, Medical engineering & physics.

[10]  Stijn Derammelaere,et al.  Efficiency measurement campaign on gearboxes , 2015 .

[11]  R. W. Daniel,et al.  On the use of differential drives for overcoming transmission nonlinearities , 1998, J. Field Robotics.

[12]  Stijn Derammelaere,et al.  Energy efficiency measurement procedure for gearboxes in their entire operating range , 2014, 2014 IEEE Industry Application Society Annual Meeting.

[13]  Jacek F. Gieras,et al.  Permanent magnet motor technology : design and applications , 1996 .

[14]  Stefano Stramigioli,et al.  Inertia-Driven Controlled Passive Actuation , 2015 .

[15]  Albert Wang,et al.  Design principles for highly efficient quadrupeds and implementation on the MIT Cheetah robot , 2013, 2013 IEEE International Conference on Robotics and Automation.

[16]  A. Galip Ulsoy,et al.  A passive-assist design approach for improved reliability and efficiency of robot arms , 2011, 2011 IEEE International Conference on Robotics and Automation.

[17]  Dirk Lefeber,et al.  Modeling and design of geared DC motors for energy efficiency: Comparison between theory and experiments , 2015 .

[18]  F. Bahrami,et al.  Distributed series elastic actuator: Analysis and simulations , 2012, 2012 12th International Conference on Control, Automation and Systems.

[19]  Andy Abate,et al.  Mechanical Antagonism in Legged Robots , 2016, Robotics: Science and Systems.

[20]  Tian-Hua Liu,et al.  Wide-range adjustable speed control method for dual-motor drive systems , 2014 .

[21]  Hugh M. Herr,et al.  Continuously-variable series-elastic actuator , 2013, 2013 IEEE 13th International Conference on Rehabilitation Robotics (ICORR).

[22]  Anye Ren,et al.  Study on a variable stiffness actuation with differential drives , 2016, 2016 IEEE International Conference on Cyber Technology in Automation, Control, and Intelligent Systems (CYBER).

[23]  Jae-Bok Song,et al.  Improved manipulation efficiency using a serial-type dual actuator unit , 2007, 2007 International Conference on Control, Automation and Systems.

[24]  Thomas G. Sugar,et al.  Compliant Mechanisms for Robotic Ankles , 2013 .

[25]  John Kenneth Salisbury,et al.  Parallel-Coupled Micro-Macro Actuators , 1996, Int. J. Robotics Res..

[26]  Nikolaos G. Tsagarakis,et al.  Design Optimisation and Control of Compliant Actuation Arrangements in Articulated Robots for Improved Energy Efficiency , 2016, IEEE Robotics and Automation Letters.

[27]  R. W. Daniel,et al.  On the use of differential drives for overcoming transmission nonlinearities , 1998 .

[28]  Vincent Babin,et al.  A dual-motor robot joint mechanism with epicyclic gear train , 2014, 2014 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[29]  Michael R. Zinn,et al.  A New Actuation Approach for Human Friendly Robot Design , 2004, Int. J. Robotics Res..

[30]  Giacomo Mantriota,et al.  An Innovative Design of Artificial Knee Joint Actuator With Energy Recovery Capabilities , 2016 .

[31]  Manuel G. Catalano,et al.  Variable impedance actuators: A review , 2013, Robotics Auton. Syst..

[32]  H. Harry Asada,et al.  A two-speed actuator for robotics with fast seamless gear shifting , 2015, 2015 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS).

[33]  H. Harry Asada,et al.  Leveraging Natural Load Dynamics With Variable Gear-Ratio Actuators , 2017, IEEE Robotics and Automation Letters.

[34]  Stefano Stramigioli,et al.  Motor-gearbox selection for energy efficiency , 2016, 2016 IEEE International Conference on Advanced Intelligent Mechatronics (AIM).

[35]  S. Stramigioli,et al.  A concept for a new Energy Efficient actuator , 2008, 2008 IEEE/ASME International Conference on Advanced Intelligent Mechatronics.

[36]  Martin Otter,et al.  Modeling and Simulating the Efficiency of Gearboxes and of Planetary Gearboxes , 2002 .

[37]  Martijn Wisse,et al.  Statically balanced brakes , 2016 .

[38]  Bruno Dehez,et al.  Variable Stiffness Actuator applied to an active ankle prosthesis: Principle, energy-efficiency, and control , 2012, 2012 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[39]  Youngjin Choi,et al.  A New Actuator System Using Dual-Motors and a Planetary Gear , 2012, IEEE/ASME Transactions on Mechatronics.