Rotary mode ultrasonic drilling of glass fiber-reinforced epoxy laminates

The use of polymer–matrix composites in structural applications necessitates certain degree of machining operations to meet the final product integrity. Drilling is an essential machining operation being used in composite industries for making of holes for bolted joints. The conventional drilling, which is frequently used for making holes in polymer–matrix composite parts, is not convenient anymore because of plethora of challenges encountered. The major drawback is the drilling-induced damage, which mainly occurs due to the direct interaction between the tool and composite laminate. Therefore, there exists a research opportunity to develop cost-effective high-quality machining methods for composite laminates. In the present research endeavor, rotary-mode ultrasonic drilling process has been conceptualized and developed for the drilling of fiber-reinforced polymer composites. The influence of various process parameters including power rating, slurry concentration, and abrasive size on material-removal rate, tool wear rate, and average surface roughness (Ra) has been experimentally investigated. It has been observed that the entry and exit delamination is prevented, and hole circumferential edge quality is improved when holes are produced through rotary-mode ultrasonic drilling as compared to the conventional drilling. It has also been found that with substantial modification in the conventional ultrasonic drilling process, the drilling performance in terms of material-removal rate of glass-epoxy laminates can be significantly improved. The major contribution of the present research endeavor is the development of a novel method of making clean-cut damage-free holes in fiber-reinforced composite laminates.

[1]  E. Kilickap.  Analysis and modeling of delamination factor in drilling glass fiber reinforced plastic using response surface methodology , 2011 .

[2]  Usama A. Khashaba,et al.  Drilling of polymer matrix composites: A review , 2013 .

[3]  Zhijian Pei,et al.  Rotary ultrasonic machining of carbon fiber-reinforced plastic composites: using cutting fluid vs. cold air as coolant , 2012 .

[4]  Xin Wang,et al.  Investigation on thrust in vibration drilling of fiber-reinforced plastics , 2004 .

[5]  K. Palanikumar,et al.  Delamination Analysis in Drilling of CFRP Composites Using Response Surface Methodology , 2009 .

[6]  A. Abrão,et al.  Influence of Drill Point Angle in High Speed Drilling of Glass Fiber Reinforced Plastics , 2008 .

[7]  W. Cong,et al.  Rotary ultrasonic machining of CFRP: A comparison with twist drilling , 2012 .

[8]  A. Abrão,et al.  Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites , 2008 .

[9]  S. Aoki,et al.  Prevention of Delamination during Drilling of Composite Material Using Vibration , 2004 .

[10]  Anil Srivastava,et al.  Rotary ultrasonic machining of CFRP composites: a study on power consumption. , 2012, Ultrasonics.

[11]  S. Aoki,et al.  Prevention from Delamination of Composite Material during Drilling Using Ultrasonic Vibration , 2005 .

[12]  A. Abrão,et al.  Drilling of fiber reinforced plastics: A review , 2007 .

[13]  Deyuan Zhang,et al.  Feasibility study of the rotary ultrasonic elliptical machining of carbon fiber reinforced plastics (CFRP) , 2012 .

[14]  Janakarajan Ramkumar,et al.  Effect of workpiece vibration on drilling of GFRP laminates , 2004 .

[15]  W. König,et al.  Quality Definition and Assessment in Drilling of Fibre Reinforced Thermosets , 1989 .

[16]  R. Krishnamurthy,et al.  Influence of tool material on dynamics of drilling of GFRP composites , 2006 .

[17]  K. Krishnamurthy,et al.  A neural network thrust force controller to minimize delamination during drilling of graphite-epoxy laminates , 1996 .

[18]  C. Treadwell,et al.  Rotary ultrasonic machining of CFRP using cold air as coolant: feasible regions , 2011 .

[19]  V. Silberschmidt,et al.  A Finite Element Model of Ultrasonically Assisted Drilling in Carbon/Epoxy Composites , 2013 .

[20]  J. Paulo Davim,et al.  Effects of high speed in the drilling of glass fibre reinforced plastic: Evaluation of the delamination factor , 2008 .

[21]  Hong Hocheng,et al.  PRELIMINARY-STUDY OF ULTRASONIC DRILLING OF FIBER-REINFORCED PLASTICS , 1995 .

[22]  J. S. Khamba,et al.  Ultrasonic machining of titanium and its alloys : A review , 2006 .

[23]  Hongwei Zhao,et al.  Mechanical model for predicting thrust and torque in vibration drilling fibre-reinforced composite materials , 2001 .

[24]  M. H. Attia,et al.  Characterization and optimization of vibration-assisted drilling of fibre reinforced epoxy laminates , 2013 .

[25]  Janakarajan Ramkumar,et al.  An enhancement of the machining performance of GFRP by oscillatory assisted drilling , 2004 .

[26]  V. Silberschmidt,et al.  Experimental and Numerical Investigations in Conventional and Ultrasonically Assisted Drilling of CFRP Laminate , 2012 .

[27]  Xiaowen Wang,et al.  Development of Empirical Models for Surface Roughness Prediction in Finish Turning , 2002 .

[28]  Jatinder Kumar,et al.  Investigating and modeling tool-wear rate in the ultrasonic machining of titanium , 2009 .

[29]  I. Singh,et al.  Drilling of composite laminates with solid and hollow drill point geometries , 2012 .

[30]  Zhang Linbo,et al.  Study on vibration drilling of fiber reinforced plastics with hybrid variation parameters method , 2003 .

[31]  M. Adithan,et al.  Tool wear studies in ultrasonic drilling , 1974 .

[32]  A. Abrão,et al.  The effect of cutting tool geometry on thrust force and delamination when drilling glass fibre reinforced plastic composite , 2008 .

[33]  Chandra Nath,et al.  Influence of the material removal mechanisms on hole integrity in ultrasonic machining of structural ceramics. , 2012, Ultrasonics.

[34]  A. Abrão,et al.  A novel approach based on digital image analysis to evaluate the delamination factor after drilling composite laminates , 2007 .

[35]  L. Vijayaraghavan,et al.  The effect of vibratory drilling on hole quality in polymeric composites , 2006 .