Arc-intersect method for 31212-axis tool paths on a 5-axis machine

Abstract An inherent problem with simultaneous 5-axis machining is that it often suffers from dramatic reductions in feed rate when the tool axis is in the vicinity of the singularity point of the machine; during large orientation changes over small distances; during rotary axes reversals and from interpolation of the tool axis vector. 3 1 2 1 2 -axis machining offers an alternative strategy that can be used to overcome these problems and still maintain some of the salient features of 5-axis machining to improve machining times over 3-axis ballnose machining. In 3 1 2 1 2 -axis machining, during cutting the machine moves only its three linear axes while the two rotary axes are locked, resulting in a fixed tool orientation. Locking the rotary axes generates fewer fluctuations in the feed rate than simultaneous 5-axis machining and results in a more consistent surface finish with lower variations in cutting force and torque. A new tool positioning strategy called the Arc-Intersect Method (AIM), which can also be applied to simultaneous 5-axis machining, is presented here for 3 1 2 1 2 -axis machining on simultaneous 5-axis machines using toroidal or flat endmills. A cutting test was performed and the part was measured with a CMM to check for accuracy and to measure the cusp heights. Machining times were compared to 5- and 3-axis tool paths and cutting torque measurements were compared between 3 1 2 1 2 - and 5-axis machining.

[1]  Sanjay E. Sarma,et al.  Collision-free finishing toolpaths from visibility data , 2003, Comput. Aided Des..

[2]  Paul J. Gray,et al.  Rolling ball method for 5-axis surface machining , 2003, Comput. Aided Des..

[3]  Zuomin Dong,et al.  Automated surface subdivision and tool path generation for 3½½-axis CNC machining of sculptured parts , 2003, Comput. Ind..

[4]  SaitoTakafumi,et al.  NC machining with G-buffer method , 1991 .

[5]  Dong-Soo Kim,et al.  A new curve-based approach to polyhedral machining , 2002, Comput. Aided Des..

[6]  Takafumi Saito,et al.  NC machining with G-buffer method , 1991, SIGGRAPH.

[7]  Robert B. Jerard,et al.  Comparison of discretization algorithms for surfaces with application to numerically controlled machining , 1997, Comput. Aided Des..

[8]  Sanjeev Bedi,et al.  Multi-point tool positioning strategy for 5-axis mashining of sculptured surfaces , 2000, Comput. Aided Geom. Des..

[9]  Paul J. Gray,et al.  Graphics-assisted Rolling Ball Method for 5-axis surface machining , 2004, Comput. Aided Des..

[10]  Dharmaraj Veeramani,et al.  Issues in patch-by-patch machining of compound sculptured surfaces , 1998 .

[11]  Paul J. Gray,et al.  Arc-intersect method for 5-axis tool positioning , 2005, Comput. Aided Des..

[12]  Sanjay E. Sarma,et al.  Generating 5-axis NC roughing paths directly from a tessellated representation , 2000, Comput. Aided Des..

[13]  Tien-Chien Chang,et al.  Three-axis machining of compound surfaces using flat and filleted endmills , 1998, Comput. Aided Des..

[14]  Bert Lauwers,et al.  Optimal and collision free tool posture in five-axis machining through the tight integration of tool path generation and machine simulation , 2003, Comput. Aided Des..

[15]  Sanjeev Bedi,et al.  Principal curvature alignment technique for machining complex surfaces , 1997 .

[16]  Paul J. Gray,et al.  Comparison of 5-Axis and 3-Axis Finish Machining of Hydroforming Die Inserts , 2001 .

[17]  Suk-Hwan Suh,et al.  Five-Axis Part Machining With Three-Axis CNC Machine and Indexing Table , 1998 .

[18]  Walter Rubio,et al.  Optimising Tool Positioning for End-Mill Machining of Free-Form Surfaces on 5-Axis Machines for both Semi-Finishing and Finishing , 2000 .

[19]  Robert B. Jerard,et al.  5-axis Machining of Sculptured Surfaces with a Flat-end Cutter , 1994, Comput. Aided Des..

[20]  Sanjeev Bedi,et al.  Tool path planning for five-axis machining using the principal axis method , 1997 .

[21]  Suk-Hwan Suh,et al.  Multiaxis machining with additional-axis NC system: Theory and development , 1998 .