Development of biporous wicks for flat-plate loop heat pipe

Abstract Two different methods, cold pressing sintering and loose powder sintering, are adopted to fabricate the biporous nickel wicks for loop heat pipes (LHPs) in the present study. Porosity of the wicks is measured by Archimedes method and radius and distribution of pores is observed by Scanning Electronic Microscope (SEM), and permeability of wicks is calculated by empirical equation. The effect of different sintering method, proportion of pore former, and sintering temperature on the wicks is investigated experimentally. Result shows that wicks are successfully fabricated, the optimal wicks are found to be sintered at 700 °C, using cold pressing sintering method, with pore former content 30% by volume; these wicks could reach the porosity of 77.40%, the permeability of 3.15 × 10 −13  m 2 , and have sufficient mechanical strength to meet the machining requirements. The effect of lathing and wire electro discharge machining on surface pores of wick is analyzed by SEM. In order to verify the performance of the biporous wick, a flat plate type of LHP is designed, fabricated and tested in this paper, and the results presents that the LHP can startup and run reliably under different heat loads.

[1]  M. Zatloukal,et al.  Experimental investigation of flow induced molecular weight fractionation phenomenon for two linear HDPE polymer melts having same Mn and Mw but different Mz and Mz+1 average molecular weights , 2012 .

[2]  A. Nakayama,et al.  Conjugate numerical analysis of flow and heat transfer with phase change in a miniature flat plate CPL evaporator , 2009 .

[3]  Chun-Nan Chen,et al.  Heat transfer analysis of a loop heat pipe with biporous wicks , 2009 .

[4]  David A. Wolf,et al.  Loop Heat Pipes - Their Performance and Potential , 1994 .

[5]  Lin Cheng,et al.  Development of sintered Ni-Cu wicks for loop heat pipes , 2009 .

[6]  Miss A.O. Penney.  (b) , 1974, The New Yale Book of Quotations.

[7]  Wei Liu,et al.  Operational characteristics of miniature loop heat pipe with flat evaporator , 2009 .

[8]  Zhengkai Tu,et al.  Heat and mass transfer in a flat disc-shaped evaporator of a miniature loop heat pipe , 2009 .

[9]  Wei Liu,et al.  Investigation of impact of different working fluids on the operational characteristics of miniature LHP with flat evaporator , 2011 .

[10]  W. Liu,et al.  Temperature Oscillation of mLHP with Flat Evaporator , 2009 .

[11]  Edson Bazzo,et al.  Development of LHPs with ceramic wick , 2010 .

[12]  Yu.F. Maydanik,et al.  Loop heat pipes , 2005 .

[13]  W. Liu,et al.  Flow and heat transfer analysis in porous wick of CPL evaporator based on field synergy principle , 2007 .

[14]  Stéphane Launay,et al.  Transient Modeling of Loop Heat Pipes for the Oscillating Behavior Study , 2007 .

[15]  Tadej Semenic,et al.  Experimental study of biporous wicks for high heat flux applications , 2009 .

[16]  Wei Liu,et al.  Experimental Investigation of New Flat-Plate-Type Capillary Pumped Loop , 2008 .

[17]  Wei Liu,et al.  Phase change driving mechanism and modeling for heat pipe with porous wick , 2009 .

[18]  K. Sreekumar,et al.  Studies on the processing of nickel base porous wicks for capillary pumped loop for thermal management of spacecrafts , 2010 .

[19]  S. K. Konev,et al.  Investigation of boiling in capillary structures , 1987 .

[20]  Tianshou Zhao,et al.  Experimental Study of Evaporative Heat Transfer in Sintered Copper Bidispersed Wick Structures , 2002 .

[21]  Edson Bazzo,et al.  Manufacturing and microstructural characterization of sintered nickel wicks for capillary pumps , 1999 .

[22]  G. P. Peterson,et al.  An Introduction to Heat Pipes: Modeling, Testing, and Applications , 1994 .

[23]  Lin Cheng,et al.  Experimental study on capillary pumping performance of porous wicks for loop heat pipe , 2010 .

[24]  L. Hourng,et al.  Numerical simulation of capillary-induced flow in a powder-embedded porous matrix , 2001 .