Monitoring of process induced strains in a single fibre composite using FBG sensor: A methodological study

A partially embedded long fibre-Bragg grating (FBG) into an epoxy cylindrical specimen is used to monitor the strain distribution evolution along its axis when subjected to subsequent cycles of thermal ageing at 70 and 110 degrees C. Assuming a total volume reduction of 2.5% at full cure, the epoxy conversion at the end of the thermal cycles was found similar to 85%. Using strain data from the FBG, the coefficient of thermal expansion was evaluated as similar to 11.5 x 10(-5) C-1. Based on the strain data from the FBG, numerical simulations of an equivalent thermo-elastic matrix were performed to obtain the residual stresses in the specimen at the end of the thermal cycles. The results demonstrate the capability of FBG sensors in providing important information on the degree of cure and evolution of fabrication induced strains inside the epoxy. (C) 2008 Elsevier Ltd. All rights reserved.

[1]  John Botsis,et al.  Characterisation of residual stresses in a single fibre composite with FBG sensor , 2007 .

[2]  Lo Yu-Lung,et al.  Measurement of thermal expansion coefficients using an in-fibre Bragg-grating sensor , 1998 .

[3]  Hyun-Kyu Kang,et al.  Simultaneous monitoring of strain and temperature during and after cure of unsymmetric composite laminate using fibre-optic sensors , 2003 .

[4]  József Karger-Kocsis,et al.  Influence of Cure Regime on the Strain Development in an Epoxy Resin as Monitored by a Fiber Bragg Grating Sensor , 2007 .

[5]  Joël Cugnoni,et al.  Experimental and numerical studies on size and constraining effects in lead-free solder joints , 2007 .

[6]  Andre Lee,et al.  A New Method to Reduce Cure-Induced Stresses in Thermoset Polymer Composites, Part III: Correlating Stress History to Viscosity, Degree of Cure, and Cure Shrinkage , 2000 .

[7]  Roberto Montanini,et al.  Simultaneous measurement of temperature and strain in glass fiber/epoxy composites by embedded fiber optic sensors: I. Cure monitoring , 2007 .

[8]  John Botsis,et al.  On a direct determination of non-uniform internal strain fields using fibre Bragg gratings , 2005 .

[9]  James S. Sirkis,et al.  Optical fiber sensor for simultaneous measurement of strain and temperature , 1997, Smart Structures.

[10]  S. White,et al.  Cure Cycle Optimization for the Reduction of Processing-Induced Residual Stresses in Composite Materials , 1993 .

[11]  Anand Asundi,et al.  Real-time cure monitoring of smart composite materials using extrinsic Fabry-Perot interferometer and fiber Bragg grating sensors , 2002 .

[12]  Gregory B. McKenna,et al.  A Viscoelastic Model for Predicting Isotropic Residual Stresses in Thermosetting Materials: Effects of Processing Parameters: , 2001 .

[13]  R P Salathé,et al.  Local coupling-coefficient characterization in fiber Bragg gratings. , 2003, Optics letters.

[14]  Andrea Cusano,et al.  Real time monitoring of cure and gelification of a thermoset matrix , 2006 .

[15]  J. D. Russell.  Cure shrinkage of thermoset composites , 1993 .

[16]  A. Snow,et al.  A simple dilatometer for thermoset cure shrinkage and thermal expansion measurements , 1994 .

[17]  J. Gillespie,et al.  Process induced stress for woven fabric thick section composite structures , 2000 .

[18]  Scott R. White,et al.  CURE-DEPENDENT VISCOELASTIC RESIDUAL STRESS ANALYSIS OF FILAMENT-WOUND COMPOSITE CYLINDERS , 1998 .

[19]  Isaac M Daniel,et al.  Determination of Chemical Cure Shrinkage in Composite Laminates , 1990 .

[20]  John W. Gillespie,et al.  Process-Induced Stress and Deformation in Thick-Section Thermoset Composite Laminates , 1992 .

[21]  G. McKenna,et al.  Cure-induced and thermal stresses in a constrained epoxy resin , 2006 .

[22]  Ralph P. Tatam,et al.  RAPID COMMUNICATION: Relating the state of cure to the real-time internal strain development in a curing composite using in-fibre Bragg gratings and dielectric sensors , 1998 .

[23]  Scott R. White,et al.  Theoretical modelling of residual and transformational stresses in SMA composites , 1996 .

[24]  Andrea Cusano,et al.  Cure-induced residual strain build-up in a thermoset resin , 2006 .

[25]  F. Ellyin,et al.  Evolution and influence of residual stresses/strains of fiber reinforced laminates , 2004 .

[26]  S. Abrate,et al.  Structural Monitoring with Fiber Optic Technology , 2001 .

[27]  Michael R Wisnom,et al.  In-situ measurement of chemical shrinkage of MY750 epoxy resin by a novel gravimetric method , 2004 .

[28]  Craig M. Lawrence,et al.  An Embedded Fiber Optic Sensor Method for Determining Residual Stresses in Fiber-Reinforced Composite Materials , 1998 .

[29]  Ivana K. Partridge,et al.  Investigation of cure induced shrinkage in unreinforced epoxy resin , 2002 .