Application of proper orthogonal decomposition and radial basis functions for crack size estimation using particle swarm optimization

Complex engineering problems require simulations, which are computationally expensive in cases of inverse identification tasks since they commonly requires hundreds of thousands of simulations. This paper propose a method based on model reduction for crack size estimation, combining the proper orthogonal decomposition method with radial basis functions. The reduced model is validated by comparing the obtained boundary displacements with the corresponding results from a finite element model. This inverse procedure is formulated as the minimization of the difference between the measured and computed values of displacement at selected boundary nodes, called sensor points, using particle swarm optimization algorithm. Convex and a non-convex specimens have been considered for investigations of crack presence, and identification of its size, different crack sizes have been tested to demonstrate the efficiency of the proposed approach.

[1]  Magd Abdel Wahab,et al.  Numerical prediction of fretting fatigue crack trajectory in a railway axle using XFEM , 2017 .

[2]  Yun-Lai Zhou,et al.  Damage detection using transmissibility compressed by principal component analysis enhanced with distance measure , 2018 .

[3]  Hung Nguyen-Xuan,et al.  Isogeometric analysis for functionally graded microplates based on modified couple stress theory , 2016, ArXiv.

[4]  Giulio Maier,et al.  Proper Orthogonal Decomposition and Radial Basis Functions in material characterization based on instrumented indentation , 2011 .

[5]  Chien H. Thai,et al.  A generalized layerwise higher-order shear deformation theory for laminated composite and sandwich plates based on isogeometric analysis , 2016 .

[6]  M. Abdel Wahab,et al.  Multiscale analysis of the effect of roughness on fretting wear , 2017 .

[7]  A. J. Kassab,et al.  Solving inverse heat conduction problems using trained POD-RBF network inverse method , 2008 .

[8]  A. Chatterjee.  An introduction to the proper orthogonal decomposition , 2000 .

[9]  Qui X. Lieu,et al.  Size-dependent isogeometric analysis of functionally graded carbon nanotube-reinforced composite nanoplates , 2017 .

[10]  N. MacDonald.  Nonlinear dynamics , 1980, Nature.

[11]  Loc V. Tran,et al.  Isogeometric analysis for nonlinear thermomechanical stability of functionally graded plates , 2016 .

[12]  Reza Hojjati-Talemi,et al.  Prediction of fretting fatigue crack initiation in double lap bolted joint using Continuum Damage Mechanics , 2015 .

[13]  M. Abdel Wahab,et al.  Finite element analysis of stress singularity in partial slip and gross sliding regimes in fretting wear , 2014 .

[14]  Bing Li,et al.  Detection of crack location and size in structures using wavelet finite element methods , 2005 .

[15]  Wei Shyy,et al.  Encyclopedia of Aerospace Engineering, 9 Volume Set , 2010 .

[16]  Magd Abdel Wahab,et al.  Numerical study for single and multiple damage detection and localization in beam-like structures using BAT algorithm , 2017 .

[17]  Magd Abdel Wahab,et al.  Finite element analysis of fretting fatigue under out of phase loading conditions , 2017 .

[18]  M. Wahab,et al.  Finite element analysis of fretting wear under variable coefficient of friction and different contact regimes , 2017 .

[19]  Vladimir Buljak.  Inverse Analyses with Model Reduction: Proper Orthogonal Decomposition in Structural Mechanics , 2011 .

[20]  D. E. Katsareas,et al.  Crack identification in frame structures , 1997 .

[21]  S. Chinchalkar.  DETERMINATION OF CRACK LOCATION IN BEAMS USING NATURAL FREQUENCIES , 2001 .

[22]  C. Rogers,et al.  An inverse POD-RBF network approach to parameter estimation in mechanics , 2012 .

[23]  L. H. Poh,et al.  Fretting fatigue stress analysis in heterogeneous material using direct numerical simulations in solid mechanics , 2017 .

[24]  Idir Belaidi,et al.  Crack identification using model reduction based on proper orthogonal decomposition coupled with radial basis functions , 2016 .

[25]  Chien H. Thai,et al.  A simple four-unknown shear and normal deformations theory for functionally graded isotropic and sandwich plates based on isogeometric analysis , 2016 .

[26]  Raphael T. Haftka,et al.  Structural and multidisciplinary optimization – special issue editorial note , 2016 .

[27]  H. V. D. Vorst,et al.  Model Order Reduction: Theory, Research Aspects and Applications , 2008 .

[28]  H. Nguyen-Xuan,et al.  An isogeometric approach for size-dependent geometrically nonlinear transient analysis of functionally graded nanoplates , 2017 .

[29]  Roger Serra,et al.  Damage detection and localization in composite beam structures based on vibration analysis , 2016 .

[30]  ScienceDirect.  Composites. Part B, Engineering , 1996 .

[31]  Loc V. Tran,et al.  Nonlinear transient isogeometric analysis of smart piezoelectric functionally graded material plates based on generalized shear deformation theory under thermo-electro-mechanical loads , 2017 .

[32]  Tadeusz Burczyński,et al.  The identification of cracks using boundary elements and evolutionary algorithms , 2001 .

[33]  Yun-Lai Zhou,et al.  Cosine based and extended transmissibility damage indicators for structural damage detection , 2017 .

[34]  Fu-Kuo Chang,et al.  Structural Health Monitoring , 2016 .

[35]  J. Chenot,et al.  An inverse analysis using a finite element model for identification of rheological parameters , 1996 .

[36]  C. Zheng,et al.  Engineering Analysis with Boundary Elements , 2017 .