An Experimental Investigation of Spur Gear Efficiency

In this study, a test methodology was developed for the measurement of spur gear efficiency under high-speed and variable torque conditions. A power-circulating test machine was designed to operate at speeds to 10,000 rpm and transmitted power levels to 700 kW. A precision torque measurement system was implemented, and its accuracy and repeatability in measuring torque loss in the power loop was demonstrated. Tests were conducted on gears with two values of modules and two surface roughness levels, operating in a dry sump jet-lubrication environment with three different gear lubricants. These tests were used to quantify the influence of these parameters on both load-dependent (mechanical), load-independent (spin), and total power loss. Trends in mechanical gear mesh efficiency and total gearbox efficiency were discussed in terms of rotational speed and transmitted torque. Finally, recommendations were made for the design of spur gear pairs, surface roughness, and lubricant selection for improved efficiency.

[1]  Li Xiao,et al.  An Experimental Study on the Effect of Surface Topography on Rough Friction in Gears , 2001 .

[2]  B. J. Hamrock,et al.  Transmission Efficiency Measurements and Correlations with Physical Characteristics of the Lubricant , 1984 .

[3]  Henry Peredur Evans,et al.  Effect of Surface Finish on Gear Tooth Friction , 2000 .

[4]  P Luke,et al.  A study of churning losses in dip-lubricated spur gears , 1999 .

[5]  Robert W. Mann,et al.  Friction Drag on Bladed Disks in Housings as a Function of Reynolds Number, Axial and Radial Clearance, and Blade Aspect Ratio and Solidity , 1961 .

[6]  Christophe Changenet,et al.  Windage Losses in High Speed Gears—Preliminary Experimental and Theoretical Results , 2004 .

[7]  David,et al.  Determining Power Losses in Helical Gear Mesh: Case Study , 2003 .

[8]  S. H. Loewenthal,et al.  Efficiency of nonstandard and high contact ratio involute spur gears , 1986 .

[9]  R. E. Nece,et al.  Chamber Dimension Effects on Induced Flow and Frictional Resistance of Enclosed Rotating Disks , 1960 .

[10]  P H Dawson.  Windage Loss in Larger High-Speed Gears , 1984 .

[11]  A. Igartua,et al.  Friction coefficient in FZG gears lubricated with industrial gear oils : Biodegradable ester vs. mineral oil , 2006 .

[12]  David Roger Chase,et al.  Development of an efficiency test methodology for high-speed gearboxes , 2005 .

[13]  Yefim Haim Michlin,et al.  Determination of power losses in gear transmissions with rolling and sliding friction incorporated , 2002 .

[14]  Fabrice Ville,et al.  Prediction of Power Losses Due to Tooth Friction in Gears , 2006 .

[15]  S. H. Loewenthal,et al.  Effect of Geometry and Operating Conditions on Spur Gear System Power Loss , 1981 .

[16]  Fabrice Ville,et al.  Experimental and Numerical Investigations on the Air-Pumping Phenomenon in High-Speed Spur and Helical Gears , 2005 .

[17]  Yasutsune Ariura,et al.  The Lubricant Churning Loss in Spur Gear Systems , 1972 .

[18]  C. Changenet,et al.  A Model for the Prediction of Churning Losses in Geared Transmissions—Preliminary Results , 2007 .

[19]  Chotaro Naruse,et al.  Study on Frictional Loss of Spur Gears (Concerning the Influence of Tooth Form, Load, Tooth Surface Roughness, and Lubricating Oil)© , 1991 .

[20]  K. F. Martin,et al.  The Efficiency of Involute Spur Gears , 1981 .

[21]  Francis E. Kennedy,et al.  Applied Tribology: Bearing Design and Lubrication , 2001 .

[22]  Chotaro Naruse,et al.  Studies on Frictional Loss, Temperature Rise and Limiting Load for Scoring of Spur Gear , 1986 .

[23]  Kazuteru Nagamura,et al.  Power Loss of Spur Gear Drive Lubricated With Traction Oil , 2003 .

[24]  Ahmet Kahraman,et al.  Prediction of Mechanical Efficiency of Parallel-Axis Gear Pairs , 2007 .

[25]  Shifeng Wu,et al.  A friction model of partial-EHL contacts and its application to power loss in spur gears , 1991 .

[26]  S. H. Loewenthal,et al.  Design of Spur Gears for Improved Efficiency , 1982 .