Passive and active gravity compensation of horizontally-mounted 3-RPS parallel kinematic machine

Abstract Taking a horizontally-mounted 3-RPS parallel kinematic machine (PKM) as an example, this paper investigates passive and active gravity compensation strategies for improving PKM precision. Herein, R, P and S denote revolute, actuated prismatic and spherical joint, respectively. Based on inverse position kinematic and force analysis, passive gravity compensation is firstly implemented by three extension springs. Geometric parameters of these springs are optimized by minimizing potential energy fluctuation within a prescribed workspace. Then deformation caused by gravity is adopted to evaluate compensation strategies. The deviations of an end reference point demonstrate that passive gravity compensation is capable of substantially balancing gravity. In order to further eliminate the effect of gravity, active gravity compensation is proposed to adjust spring displacements by several one degree-of-freedom (DoF) translational mechanisms. Deformation of the 3-RPS PKM is directly regarded as the objective function for determining the active translations. Overall, both passive and active gravity compensations are able to improve mechanism precision due to the partial and complete gravity balancing capability, respectively, which makes the 3-RPS PKM suitable for the application of rough and fine machining.

[1]  Vigen Arakelian,et al.  Improvement of balancing accuracy of robotic systems: Application to leg orthosis for rehabilitation devices , 2008 .

[2]  W D van Dorsser,et al.  Energy-free adjustment of gravity equilibrators by adjusting the spring stiffness , 2008 .

[3]  Tian Huang,et al.  Compliance analysis of a 3-DOF spindle head by considering gravitational effects , 2015 .

[4]  Clément Gosselin,et al.  Static balancing of spatial four-degree-of-freedom parallel mechanisms , 2000 .

[5]  Clément Gosselin,et al.  A Statically Balanced Gough/Stewart-Type Platform: Conception, Design, and Simulation , 2009 .

[6]  A. Deshpande,et al.  Design of Nonlinear Rotational Stiffness Using a Noncircular Pulley-Spring Mechanism , 2014 .

[7]  Sunil K. Agrawal,et al.  Design and fabrication of an active gravity balanced planar mechanism using auxiliary parallelograms , 2001 .

[8]  Tao Sun,et al.  Stiffness analysis and experiment of a novel 5-DoF parallel kinematic machine considering gravitational effects , 2015 .

[9]  Tao Sun,et al.  Stiffness analysis of a 2-DoF over-constrained RPM with an articulated traveling platform , 2016 .

[10]  Fengfeng Xi,et al.  A comparative study on tripod units for machine tools , 2003 .

[11]  Qi Yang,et al.  A Novel Five-Degree-of-Freedom Parallel Manipulator and Its Kinematic Optimization , 2014 .

[12]  Mark Yim,et al.  Modular Advantage and Kinematic Decoupling in Gravity Compensated Robotic Systems , 2013 .

[13]  Hélène Chanal,et al.  A study of the impact of machine tool structure on machining processes , 2006 .

[14]  Javaid Iqbal,et al.  On the Improvement of Multi-Legged Locomotion over Difficult Terrains Using a Balance Stabilization Method: , 2012 .

[15]  Clément Gosselin.  Static Balancing of Spherical 3-DOF Parallel Mechanisms and Manipulators , 1999, Int. J. Robotics Res..

[16]  Clément Gosselin,et al.  Adaptive gravity compensation of decoupled parallel and serial manipulators using a passive hydraulic transmission , 2009 .

[17]  Fengfeng Xi,et al.  Static balancing of parallel robots , 2005 .

[18]  Antonio Frisoli,et al.  Modelling and Experimental Evaluation of a Static Balancing Technique for a New Horizontally Mounted 3-UPU Parallel Mechanism , 2012 .

[19]  Xin-Jun Liu,et al.  A Comparison Study on Motion/Force Transmissibility of Two Typical 3-DOF Parallel Manipulators: The Sprint Z3 and A3 Tool Heads , 2014 .

[20]  Clément Gosselin,et al.  Static balancing of 3-DOF planar parallel mechanisms , 1999 .

[21]  Dar-Zen Chen,et al.  Design of a Gravity-Balanced General Spatial Serial-Type , 2010 .

[22]  Matthew O. T. Cole,et al.  Analysis of a Gravity Compensated Four-Bar Linkage Mechanism With Linear Spring Suspension , 2008 .

[23]  Dar-Zen Chen,et al.  Design of Perfectly Statically Balanced One-DOF Planar Linkages With Revolute Joints Only , 2009 .

[24]  Damien Chablat,et al.  The Design of Parallel Kinematic Machine Tools Using Kinetostatic Performance Criteria , 2007, ArXiv.