Statistical analysis of interfacial gap in a cementless stem FE model.

In cementless total hip arthroplasty, a fair amount of interfacial gap exists between the femoral stem and the bone. However, the effect of these gaps on the mechanical stability of the stem is poorly understood. In this paper, a finite element model with various interfacial gap definitions is used to quantify the effect of interfacial gaps on the primary stability of a Versys Fiber Metal Taper stem under stair climbing loads. In the first part, 500 random interfacial gap definitions were simulated. The resulting micromotion was approximately inversely proportional to the contact ratio, and the variance of the micromotion was greater with a lower contact ratio. Moreover, when the magnitude of the micromotion was compared between the gap definitions that had contact at a specific site and those that had no contact at that site, it was found that gaps located in the proximal-medial region of the stem surface had the most important effect on the micromotion. In a second trial, 17 gap definitions mimicking a gap pattern that has been observed experimentally were simulated. For a given contact ratio, the micromotion observed in the second trial was lower than the average result of those in the first, where the gaps were placed randomly. In either trial, when the contact ratio was higher than 40%, the micromotion showed no significant difference (first trial) or a gentle slope (-0.24 mum% in the second trial) in relation to the contact ratio. Considering the reported contact ratios for properly implanted stems, variations in the amount of interfacial gap would not likely cause a drastic difference in micromotion, and this effect could be easily overshadowed by other clinical factors. In conclusion, differences in interfacial gaps are not expected to have a noticeable effect on the clinical micromotion of this cementless stem.

[1]  I Macnab,et al.  The rate of bone ingrowth into porous metal. , 1976, Journal of biomedical materials research.

[2]  S. Ferguson,et al.  Primary stability of a robodoc implanted anatomical stem versus manual implantation. , 2004, Clinical biomechanics.

[3]  W. Harris,et al.  Periprosthetic bone loss in total hip arthroplasty. Polyethylene wear debris and the concept of the effective joint space. , 1992, The Journal of bone and joint surgery. American volume.

[4]  D. W. Bühler,et al.  Three-dimensional primary stability of cementless femoral stems. , 1997, Clinical biomechanics.

[5]  L Cristofolini,et al.  Initial stability of a new hybrid fixation hip stem: experimental measurement of implant-bone micromotion under torsional load in comparison with cemented and cementless stems. , 2000, Journal of biomedical materials research.

[6]  L. Nolte,et al.  Three-dimensional measurement of cemented femoral stem stability: an in vitro cadaver study. , 2000, Clinical Biomechanics.

[7]  P R Fernandes,et al.  Shape Optimization of a Cementless Hip Stem for a Minimum of Interface Stress and Displacement , 2004, Computer methods in biomechanics and biomedical engineering.

[8]  G Bergmann,et al.  Determination of muscle loading at the hip joint for use in pre-clinical testing. , 2005, Journal of biomechanics.

[9]  A. S. Wong,et al.  Influence of bone quality on the initial stability of cementless hip stem in total hip arthroplasty , 2003 .

[10]  H. Amstutz,et al.  "Modes of failure" of cemented stem-type femoral components: a radiographic analysis of loosening. , 1979, Clinical orthopaedics and related research.

[11]  Yong-San Yoon,et al.  Primary stability of cementless stem in THA improved with reduced interfacial gaps. , 2008, Journal of biomechanical engineering.

[12]  W. Bargar,et al.  Primary and Revision Total Hip Replacement Using the Robodoc® System , 1998, Clinical orthopaedics and related research.

[13]  J. Lindhe,et al.  Resolution of bone defects of varying dimension and configuration in the marginal portion of the peri-implant bone. An experimental study in the dog. , 2004, Journal of clinical periodontology.

[14]  F Amirouche,et al.  Study of micromotion in modular acetabular components during gait and subluxation: a finite element investigation. , 2008, Journal of biomechanical engineering.

[15]  Marco Viceconti,et al.  Primary stability of an anatomical cementless hip stem: a statistical analysis. , 2006, Journal of biomechanics.

[16]  Angelo Cappello,et al.  Comparative in vitro study on the long term performance of cemented hip stems: validation of a protocol to discriminate between "good" and "bad" designs. , 2003, Journal of biomechanics.

[17]  R M Pilliar,et al.  Osteogenic phenomena across endosteal bone-implant spaces with porous surfaced intramedullary implants. , 1981, Acta orthopaedica Scandinavica.

[18]  Wolfgang Görtz,et al.  Robotically-milled bone cavities , 2002, Acta orthopaedica Scandinavica.

[19]  C. Engh,et al.  What We Have Learned About Long-Term Cementless Fixation From Autopsy Retrievals , 2002, Clinical orthopaedics and related research.

[20]  Mark H. Gonzalez,et al.  Experimental and analytical validation of a modular acetabular prosthesis in total hip arthroplasty , 2007, Journal of orthopaedic surgery and research.

[21]  J. M. Lee,et al.  Observations on the Effect of Movement on Bone Ingrowth into Porous‐Surfaced Implants , 1986, Clinical orthopaedics and related research.

[22]  T. Krüger,et al.  ROBODOC - Ein Weg in die Zukunft der Hüftendoprothetik oder eine Fehlinvestition? , 2000 .

[23]  H Nägerl,et al.  Spatial micromovements of uncemented femoral components after torsional loads. , 2002, Journal of biomechanical engineering.

[24]  J. Galante,et al.  Impacted particulate allograft for femoral revision total hip arthroplasty. In vitro mechanical stability and effects of cement pressurization. , 1996, The Journal of arthroplasty.

[25]  L Cristofolini,et al.  Large-sliding contact elements accurately predict levels of bone-implant micromotion relevant to osseointegration. , 2000, Journal of biomechanics.

[26]  J Hassenpflug,et al.  The dimensional accuracy of preparation of femoral cavity in cementless total hip arthroplasty , 2004, Journal of Zhejiang University. Science.

[27]  H. Baba,et al.  Nonlinear three-dimensional finite element analysis of newly designed cementless total hip stems. , 1999, Artificial organs.

[28]  M. Viceconti,et al.  Even a thin layer of soft tissue may compromise the primary stability of cementless hip stems. , 2001, Clinical biomechanics.

[29]  Robert B Bourne,et al.  A quantitative analysis of bone support comparing cementless tapered and distal fixation total hip replacements. , 2004, The Journal of arthroplasty.