Microcapsule-based self-healing anticorrosive coatings: Capsule size, coating formulation, and exposure testing

Abstract Self-healing coatings is a rapidly growing research area, where focus has mainly been on development of new approaches to the mechanism of self-healing. However, there is a growing need for investigation of practical issues related to formulation, application, and testing of true self-healing coatings. In this work, ways of reducing the size of poly(urea–formaldehyde) microcapsules, filled with linseed oil and intended for a microcapsule-based self-healing anticorrosive coating (above water exposure), are explored. The influence of microcapsules on epoxy coating performance is also studied. The actual self-healing effect was not part of this work. The synthesis parameters investigated are stirrer geometry, agitation rate, temperature, and stabilizer concentration. It was found that an increase in stirring rate, correct choice of temperature, and a high stabilizer concentration all caused a decrease in microcapsule size but were accompanied by excessive formation of nanoparticles. Thus, isolation of too large microcapsules has been performed by filtration utilizing a novel low-energy fluoropolymer-coated steel sieve. An estimation of the critical pigment (microcapsule) volume concentration (CPVC) was conducted using gloss measurements and a PVC ladder and found to be about 30 vol%. Due to the rather large capsules used (relative to the coating thickness), the low CPVC value can probably be ascribed to a fairly low packing efficiency in the coating, but this needs to be confirmed. Coating performance was evaluated using salt spray exposure and impact testing. Results of the impact testing showed that addition of microcapsules to a binder matrix did not compromise resistance of the coating to mechanical damage and led to formation of fewer and shorter cracks compared to a filler-containing coating. Flaking of the coating was also reduced. Results of the salt spray testing (3 weeks exposure) showed that with an increase of microcapsule content, in the interval 30–50 vol%, the extent of corrosion and potential coating delamination decreased and was identical to that of a full commercial anticorrosive coating.

[1]  N. Sottos,et al.  In situ poly(urea-formaldehyde) microencapsulation of dicyclopentadiene , 2003, Journal of microencapsulation.

[2]  Kim Dam-Johansen,et al.  Synthesis of durable microcapsules for self-healing anticorrosive coatings: A comparison of selected methods , 2011 .

[3]  Li Yuan,et al.  Preparation and characterization of poly(urea-formaldehyde) microcapsules filled with epoxy resins , 2006 .

[4]  W. K. Asbeck,et al.  Critical Pigment Volume Relationships. , 1949 .

[5]  Krzysztof Matyjaszewski,et al.  Self-Healing Polymer Films Based on Thiol-Disulfide Exchange Reactions and Self-Healing Kinetics Measured Using Atomic Force Microscopy , 2012 .

[6]  N. Sottos,et al.  Autonomic healing of polymer composites , 2001, Nature.

[7]  Wayne Hayes,et al.  Healable polymeric materials: a tutorial review. , 2010, Chemical Society reviews.

[8]  J. Baghdachi,et al.  Design and Development of Self-Healing Polymers and Coatings , 2010 .

[9]  M. El-Aasser,et al.  Influence of particle surface properties on film formation from precipitated calcium carbonate/latex blends , 2002 .

[10]  M. El-Aasser,et al.  Film formation from pigmented latex systems: Mechanical and surface properties of ground calcium carbonate/functionalized poly(n‐butyl methacrylate‐co‐n‐butyl acrylate) latex blend films , 2006 .

[11]  A. Hughes,et al.  Self-healing anticorrosive organic coating based on an encapsulated water reactive silyl ester: Synthesis and proof of concept , 2011 .

[12]  S. Zwaag,et al.  A critical appraisal of the potential of self healing polymeric coatings , 2011 .

[13]  Frank N. Jones,et al.  Organic Coatings: Science and Technology , 1992 .

[14]  W. Ming,et al.  Self healing polymer coatings , 2007 .

[15]  A. Gu,et al.  Preparation and properties of poly(urea–formaldehyde) microcapsules filled with epoxy resins , 2008 .

[16]  N. Sottos,et al.  In situ poly(urea-formaldehyde) microencapsulation of dicyclopentadiene , 2003 .

[17]  Michael R. Kessler,et al.  Synthesis and Characterization of Melamine-Urea-Formaldehyde Microcapsules Containing ENB-Based Self-Healing Agents , 2009 .

[18]  S. Gibson,et al.  Determination of the critical pigment volume concentrations of pigmented film coating formulations using gloss measurement , 1988 .

[19]  J. Bognar,et al.  Self-healing microcapsules and slow release microspheres in paints , 2011 .

[20]  Nancy R. Sottos,et al.  Accelerated Self‐Healing Via Ternary Interpenetrating Microvascular Networks , 2011 .

[21]  Ali Ashrafi,et al.  A review on self-healing coatings based on micro/nanocapsules , 2010 .

[22]  D. Wu,et al.  Self-healing polymeric materials: A review of recent developments , 2008 .

[23]  G. Bierwagen,et al.  The reduced pigment volume concentration as an important parameter in interpreting and predicting the properties of organic coatings , 1975 .

[24]  K. Dam-Johansen,et al.  Anticorrosive coatings: a review , 2009 .

[25]  Dhirendra Kumar,et al.  Preparation and characterization of microcapsules containing linseed oil and its use in self-healing coatings , 2008 .

[26]  Artur Goldschmidt,et al.  BASF Handbook Basics of Coating Technology , 2003 .

[27]  Fred Wudl,et al.  The world of smart healable materials , 2010 .

[28]  S. Zwaag.  Self‐Healing Materials , 2007 .

[29]  M. Rong,et al.  A novel method for preparing epoxy-containing microcapsules via UV irradiation-induced interfacial copolymerization in emulsions , 2007 .

[30]  Ali Ashrafi,et al.  Tung oil: An autonomous repairing agent for self-healing epoxy coatings , 2011 .