Validation of the DALTON-THERMIX Code System with Transient Analyses of the HTR-10 and Application to the PBMR

Abstract The DALTON-THERMIX code system has been developed for safety analysis and core optimization of pebble-bed reactors. The code system consists of the new three-dimensional diffusion code DALTON, which is coupled to the existing thermal-hydraulic code THERMIX. These codes are linked to a database procedure for the generation of neutron cross sections using SCALE-5. The behavior of pebble-bed reactors during a loss of forced cooling (LOFC) transient is of particular interest since the absence of forced cooling could lead to a significant increase of the temperature of the coated particle fuel. Therefore, the reactor power may be constrained during normal operation to limit the temperature. For validation purposes, calculation results of normal operation, an LOFC transient, and a control rod withdrawal transient without SCRAM have been compared with experimental data obtained in the High Temperature Reactor–10 (HTR-10). The code system has been applied to the 400-MW(thermal) pebble bed modular reactor (PBMR) design, including the analysis of three different LOFC transients. Theses results are verified by a comparison with the results of the existing TINTE code system. It was found that the code system is capable of modeling both small (HTR-10) and large (PBMR) pebble-bed reactors and therefore provides a flexible tool for safety analysis and core optimization of future reactor designs. The analyses of the LOFC transients show that the peak fuel temperature is only slightly elevated (less than +100°C) as compared to its nominal value in the HTR-10 but reaches a maximum value of 1648°C during the depressurized LOFC case of the PBMR benchmark, which is significantly higher than the peak fuel temperature (976°C) during normal operation.

[1]  Lei Shi,et al.  Thermal hydraulic calculation of the HTR-10 for the initial and equilibrium core , 2002 .

[2]  J. E. Morel,et al.  A fission-source acceleration technique for time-dependent even-parity Sn calculations , 1994 .

[3]  W. Lafayette,et al.  The OECD/NEA/NSC PBMR coupled neutronics/thermal hydraulics transient benchmark: The PBMR-400 core design , 2006 .

[4]  Gunter H. Lohnert,et al.  The Modular High-Temperature Reactor , 1983 .

[5]  Shuoping Zhong,et al.  Temperature Measuring System of the In-core Components for Chinese 10 MW High Temperature Gas-cooled Reactor , 2002 .

[6]  Chao Yang,et al.  ARPACK users' guide - solution of large-scale eigenvalue problems with implicitly restarted Arnoldi methods , 1998, Software, environments, tools.

[7]  Zhengpei Luo,et al.  Fuel management of the HTR-10 including the equilibrium state and the running-in phase , 2002 .

[8]  M. Ding,et al.  Evaluation of experiments in the AVR with the DALTON-THERMIX coupled code system , 2009 .

[9]  Jonghwa Chang,et al.  DEVELOPMENT OF MARS-GCR/V1 FOR THERMAL-HYDRAULIC SAFETY ANALYSIS OF GAS- COOLED REACTOR SYSTEMS , 2005 .

[10]  Andreas Pautz,et al.  DORT-TD: A Transient Neutron Transport Code with Fully Implicit Time Integration , 2003 .

[11]  W. K. Terry,et al.  Direct Deterministic Method for Neutronics Analysis and Computation of Asymptotic Burnup Distribution in a Recirculating Pebble-Bed Reactor , 2002 .

[12]  H. Gerwin,et al.  The TINTE Modular Code System for Computational Simulation of Transient Processes in the Primary Circuit of a Pebble-Bed High-Temperature Gas-Cooled Reactor , 1989 .

[13]  Xingqing Jing,et al.  Prediction calculations and experiments for the first criticality of the 10 MW High Temperature Gas-cooled Reactor-Test Module , 2002 .

[14]  T. Ono,et al.  Experimental Verification and Analysis of Neutron Streaming Effect through Void Holes for Control Rod Insertion in HTTR , 1997 .

[15]  B. Boer,et al.  In-core fuel management optimization of pebble-bed reactors , 2009 .

[16]  Zuying Gao,et al.  Transient tests on blower trip and rod removal at the HTR-10 , 2006 .

[17]  Dieter Matzner,et al.  PBMR PROJECT STATUS AND THE WAY AHEAD , 2004 .

[18]  W. Scherer,et al.  Treatment of the upper cavity in a pebble-bed high-temperature gas-cooled reactor by diffusion theory , 1987 .

[19]  David L. Hetrick,et al.  Introductory Nuclear Reactor Dynamics , 1987 .

[20]  Jim E. Morel,et al.  A Two-Grid Acceleration Scheme for the Multigroup Sn Equations with Neutron Upscattering , 1993 .

[21]  Jan Leen Kloosterman,et al.  Analytical Calculation of the Average Dancoff Factor for a Fuel Kernel in a Pebble Bed High-Temperature Reactor , 1999 .

[22]  U. S. Doe.  A Technology Roadmap for Generation IV Nuclear Energy Systems , 2002 .

[23]  Han Gyu,et al.  PARCS: PURDUE ADVANCED REACTOR CORE SIMULATOR Thomas J. Downar Douglas A. Barber 1 R. Matthew Miller Chang-Ho Lee Tomasz Kozlowski Deokjung Lee Yunlin Xu Jun Gan , 2002 .

[24]  Kostadin Ivanov,et al.  Utilization of two-dimensional deterministic transport methods for analysis of pebble-bed reactors , 2007 .

[25]  Danny Lathouwers,et al.  Coupled neutronics / thermal hydraulics calculations for High Temperature Reactors with the DALTON - THERMIX code system , 2008 .

[26]  Frederik Reitsma.  The Pebble Bed Modular Reactor Layout and Neutronics Design of the Equilibrium Cycle , 2004 .