A New Integrated Approach for the Prediction of the Load Independent Power Losses of Gears: Development of a Mesh-Handling Algorithm to Reduce the CFD Simulation Time

To improve the efficiency of geared transmissions, prediction models are required. Literature provides only simplified models that often do not take into account the influence of many parameters on the power losses. Recently some works based on CFD simulations have been presented. The drawback of this technique is the time demand needed for the computation. In this work a less time-consuming numerical calculation method based on some specific mesh-handling techniques was extensively applied. With this approach the windage phenomena were simulated and compared with experimental data in terms of power loss. The comparison shows the capability of the numerical approach to capture the phenomena that can be observed experimentally. The powerful capabilities of this approach in terms of both prediction accuracy and computational effort efficiency make it a potential tool for an advanced design of gearboxes as well as a powerful tool for further comprehension of the physics behind the gearbox lubrication.

[1]  P Luke,et al.  A study of churning losses in dip-lubricated spur gears , 1999 .

[2]  Carlo Gorla,et al.  Influence Of Lubricant Temperature, Lubricant Level And Rotational Speed On The Churning Power Loss In An Industrial Planetary Speed Reducer: Computational And Experimental Study , 2013 .

[3]  Augusto Della Torre,et al.  CFD Simulation of a Sliding Vane Expander Operating Inside a Small Scale ORC for Low Temperature Waste Heat Recovery , 2014 .

[4]  Tommaso Lucchini,et al.  Automatic Mesh Generation for CFD Simulations of Direct-Injection Engines , 2015 .

[5]  Ahmet Kahraman,et al.  Load-Independent Spin Power Losses of a Spur Gear Pair: Model Formulation , 2009 .

[6]  Carlo Gorla,et al.  Oil Squeezing Power Losses In Gears:A CFD Analysis , 2012 .

[7]  J.-P. Stemplinger,et al.  Hydraulic losses of a gearbox: CFD analysis and experiments , 2013 .

[8]  Fabrice Ville,et al.  Investigations on CFD Simulations for Predicting Windage Power Losses in Spur Gears , 2009 .

[9]  Carlo Gorla,et al.  Analysis of the Oil Squeezing Power Losses of a Spur Gear Pair by Mean of CFD Simulations , 2012 .

[10]  Bernd-Robert Höhn,et al.  Influences on no-load Gear Losses , 2011 .

[11]  J.-P. Stemplinger,et al.  CFD Simulations of Splash Losses of a Gearbox , 2012 .

[12]  Sheng Li,et al.  Prediction of Mechanical Power Loss of Planet Gear Roller Bearings Under Combined Radial and Moment Loading , 2013 .

[13]  Weeratunge Malalasekera,et al.  An introduction to computational fluid dynamics - the finite volume method , 2007 .

[14]  Robert F. Handschuh,et al.  CFD Analysis of Gear Windage Losses: Validation and Parametric Aerodynamic Studies , 2011 .

[15]  Carlo Gorla,et al.  Computational And Experimental AnalysisOf The Churning Power Losses In An IndustrialPlanetary Speed Reducer , 2012 .

[16]  P H Dawson.  Windage Loss in Larger High-Speed Gears , 1984 .

[17]  Augusto Della Torre,et al.  Churning power losses of ordinary gears: a new approach based on the internal fluid dynamics simulations , 2015 .

[18]  Augusto Della Torre,et al.  Windage Power Losses of Ordinary Gears: Different CFD Approaches Aimed to the Reduction of the Computational Effort , 2014 .

[19]  Sheng Li,et al.  Prediction of Spur Gear Mechanical Power Losses Using a Transient Elastohydrodynamic Lubrication Model , 2010 .

[20]  Carlo Gorla,et al.  Analysis of power losses in an industrial planetary speed reducer: Measurements and computational fluid dynamics calculations , 2014 .

[21]  Carlo Gorla,et al.  A CFD ANALYSIS OF THE OIL SQUEEZING POWER LOSSES OF A GEAR PAIR , 2014 .