Scratch and wear performance of prosthetic femoral head components against crosslinked UHMWPE sockets

Total hip arthroplasty is a highly successful procedure where the hip joint is replaced by an artificial ball and socket joint. Bearing wear continues to be a contributing factor to implant failure. Prosthetic femoral heads roughen in vivo which leads to increased wear. Along with the introduction of improved polyethylene which reduces wear by up to 99%, improved femoral head materials have been introduced to improve resistance to abrasion. The abrasion resistance of two of these improved femoral heads was assessed in this study and compared to a cobalt chromium (CoCr) femoral head. The resulting wear performance against a polyethylene acetabular component was assessed. The bulk ceramic (zirconia toughened alumina) femoral head exhibited superior abrasion resistance compared to CoCr (97% reduction in damage) as well as reduced wear after abrasion (97% reduction in wear). The oxide coated zirconium niobium femoral head showed inferior abrasion resistance compared to CoCr (99% increase in damage) as well as increased wear after abrasion (161% increase in wear). Both femoral head surfaces utilize hard ceramic materials, however, the thin ceramic coating on top of a softer metallic substrate of the oxide coated bearing was unable to withstand aggressive abrasion.

[1]  I C Clarke,et al.  Mechanism and clinical significance of wear debris-induced osteolysis. , 1992, Clinical orthopaedics and related research.

[2]  A. Unsworth,et al.  The effect of ‘running-in’ on the tribology and surface morphology of metal-on-metal Birmingham hip resurfacing device in simulator studies , 2006, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[3]  R. Bourne,et al.  Metal-on-Metal Versus Polyethylene in Hip Arthroplasty: A Randomized Clinical Trial , 2003, Clinical orthopaedics and related research.

[4]  W H Harris,et al.  Surface damage to cobalt-chrome femoral head prostheses. , 1994, The Journal of bone and joint surgery. British volume.

[5]  V. Good,et al.  Reduced Wear with Oxidized Zirconium Femoral Heads , 2003, The Journal of bone and joint surgery. American volume.

[6]  W. Harris,et al.  Periprosthetic bone loss in total hip arthroplasty. Polyethylene wear debris and the concept of the effective joint space. , 1992, The Journal of bone and joint surgery. American volume.

[7]  B. M. Wroblewski,et al.  The surface topography of retrieved femoral heads , 1996 .

[8]  A. Wang,et al.  Wear mechanisms of UHMWPE in total joint replacements , 1995 .

[9]  N. Baldini,et al.  Ion release in patients with metal-on-metal hip bearings in total joint replacement: a comparison with metal-on-polyethylene bearings. , 2002, Journal of biomedical materials research.

[10]  A. Kop,et al.  Damage of oxinium femoral heads subsequent to hip arthroplasty dislocation three retrieval case studies. , 2007, The Journal of arthroplasty.

[11]  A. Essner,et al.  Hip simulator evaluation of the effect of femoral head size on sequentially cross-linked acetabular liners☆ , 2007 .

[12]  Aiguo Wang,et al.  The Basis for a Second-generation Highly Cross-linked UHMWPE , 2006, Clinical orthopaedics and related research.

[13]  B. W. Schreurs,et al.  High Incidence of Squeaking in THAs with Alumina Ceramic-on-ceramic Bearings , 2008, Clinical orthopaedics and related research.

[14]  A. Unsworth,et al.  The influence of femoral head surface roughness on the wear of ultrahigh molecular weight polyethylene sockets in cementless total hip replacement. , 1999, Journal of biomedical materials research.

[15]  W. Brodner,et al.  Cup inclination and serum concentration of cobalt and chromium after metal-on-metal total hip arthroplasty. , 2004, The Journal of arthroplasty.

[16]  W. Walter,et al.  Squeaking in ceramic-on-ceramic hips: the importance of acetabular component orientation. , 2007, The Journal of arthroplasty.

[17]  A. Wang,et al.  Wear, oxidation and mechanical properties of a sequentially irradiated and annealed UHMWPE in total joint replacement , 2006 .

[18]  A. Wang,et al.  The effects of lubricant composition on in vitro wear testing of polymeric acetabular components. , 2004, Journal of biomedical materials research. Part B, Applied biomaterials.

[19]  A. Wang,et al.  Three-body wear of UHMWPE acetabular cups by PMMA particles against CoCr, alumina and zirconia heads in a hip joint simulator , 2001 .