Effects of Grain Boundary Sliding on Microstructural Evolution and Damage Accumulation in Tin-Lead Alloy

Experiments on the eutectic tin-lead (Sn-Pb) alloys were conducted to study the effects of grain boundary sliding on the deformation and damage processes at the microscopic level. The primary objective is to gain mechanistic undersanding of solder joint reliability in microelectronic packaging. Bulk specimens were subjected to relatively fast deformations of tension, compression, and bending, for the purposes of examining the pure mechanical effect without the influence of diffusion-related phenomena. Grain realignment and phase redistribution were characterized by microscopy and microhardness indentation. A micromechanical model is proposed to elucidate the observed microstructural changes and progressive damage. This study illustrates the significance of damage in the form of microscopic heterogeneity caused by grain boundary sliding. It also illustrates the possibility of mechanically induced phase coarsening in actual solder joints. High-frequency cyclic shear tests on Sn-Pb solder joints showed damage along the coarsened band after only a short time, in accord with the proposed effects. Boundary sliding without the influence of atomic diffusion plays an essential role in fatigue damage in solder.

[1]  D. Frear,et al.  Time-dependent deformation behavior of near-eutectic 60Sn-40Pb solder , 1999 .

[2]  H. E. Fang,et al.  Phase Structure and Cyclic Deformation in Eutectic Tin-Lead Alloy: A Numerical Analysis , 2001 .

[3]  D. Frear.  The Mechanics of Solder Alloy Interconnects , 1993 .

[4]  Y. Pao,et al.  Fatigue-creep crack propagation path in solder joints under thermal cycling , 1997 .

[5]  S. Hori,et al.  Direct determination of the strain rate sensitivity of flow stresses based on grain boundary sliding in a SnPb eutectic during superplastic and non-superplastic deformation , 1979 .

[6]  W. Gust,et al.  Interface diffusion in eutectic Pb–Sn solder , 1998 .

[7]  Microstructural changes in eutectic tin–lead alloy due to severe bending , 2001 .

[8]  T. Langdon,et al.  An investigation of intercrystalline and interphase boundary sliding in the superplastic Pb-62% Sn eutectic , 1979 .

[9]  W. J. Plumbridge,et al.  Solders in electronics , 1996, Journal of Materials Science.

[10]  A. Mukherjee,et al.  The direct observation of cooperative grain‐boundary sliding and migration during superplastic deformation of lead‐tin eutectic in shear , 1993 .

[11]  C. R. Barrett,et al.  Superplastic deformation of the Pb-Sn eutectic , 1976 .

[12]  N. Grant,et al.  Observations of grain boundary sliding during superplastic deformation , 1983 .

[13]  Michael F. Ashby,et al.  Diffusion-accommodated flow and superplasticity , 1973 .

[14]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[15]  Y. Fahmy,et al.  Phase coarsening and crack growth rate during thermo-mechanical cycling of 63Sn37Pb solder joints , 1998 .

[16]  R. Valiev,et al.  An investigation of the role of intragranular dislocation strain in the superplastic Pb-62% Sn eutectic alloy , 1993 .

[17]  Hans Conrad,et al.  Effect of Microstructure Size on Deformation Kinetics and Thermo-Mechanical Fatigue of 63Sn37Pb Solder Joints , 1996 .

[18]  A. Mukherjee,et al.  Microstructural aspects of superplasticity , 1985 .

[19]  Paul T. Vianco,et al.  Coarsening of the Sn-Pb solder microstructure in constitutive model-based predictions of solder joint thermal mechanical fatigue , 1999 .

[20]  G. Chadwick,et al.  Grain boundary structure and properties , 1976 .

[21]  H. E. Fang,et al.  Characteristics of Creep Damage for 60 Sn-40 Pb Solder Material , 1999 .

[22]  P. Schiller,et al.  Observation of processes of superplasticity with the scanning electron microscope , 1975 .

[23]  M. Fine,et al.  Isothermal Fatigue of 63Sn-37Pb Solder , 1990 .