Abstract Since its launch on November 4, 1995 and the start of the routine operation on April 1, 1996, RADARSAT-1, the first Canadian Synthetic Aperture Radar (SAR) remote sensing satellite, has provided calibrated data to worldwide users for their intended applications. From the early qualification stages of the mission, both single beams and ScanSAR operating modes are monitored routinely for radiometric calibration performance using images of the Amazon Rainforest, and for image quality performance using images of RADARSAT-1 Precision Transponders. After the initial Calibration Phase and the Antarctic Mapping Mission in 1997, a systematic calibration monitoring strategy showed changes in the characteristics of several previously calibrated elevation antenna patterns. Compensations for these changes are made in the processor by re-calibrating the beams. In addition, a major upgrade of the ScanSAR processor completed at the Canadian Data Processing Facility (CDPF) in 2002 yielded to significant improvements in image quality and radiometry. Throughout the nominal mission life of 5 years and the 3 years of the current extended mission, which started in early 2001, the Canadian Data Processing Facility continued to provide radiometrically and geometrically calibrated RADARSAT-1 products to users. In late October 2000, concerns began to rise of the possibility of failure of the Horizon Scanner 1, which would result in operating the spacecraft in a mode known as ‘Attitude Determination Method 3’ (ADM3), causing a decrease in attitude control performance of the spacecraft compared to the current operation in primary ADM1. Experiments were conducted to better understand the impact on processing and image quality when in ADM3 mode. No major impact on image quality was noticed with adapted re-processing. In mid 2002, due to aging considerations for the On-Board Recorder, natural sites within Canadian data reception masks have been envisioned for their potential to support radiometric analyses, as an alternative to the Amazon Rainforest where images are recorded. From several sites, a Boreal Forest location near Hearst, Ontario, Canada was chosen for testing radiometric measurements, using specific beams to cover the entire range of incidence angles.
[1]
Kevin Murnaghan,et al.
Maintenance of Radiometric Calibration Performance of RADARSAT-1
,
2000
.
[2]
S. Ahmed,et al.
RADARSAT Mission Requirements and Concept
,
1993
.
[3]
T. I. Lukowski,et al.
RADARSAT-1 image quality and calibration — a continuing success
,
2001
.
[4]
T. I. Lukowski,et al.
RADARSAT image quality and calibration — Update
,
1999
.
[5]
M. Adamovic,et al.
Statistical methodology for monitoring radiometric performance of RADARSAT-1
,
2000,
IGARSS 2000. IEEE 2000 International Geoscience and Remote Sensing Symposium. Taking the Pulse of the Planet: The Role of Remote Sensing in Managing the Environment. Proceedings (Cat. No.00CH37120).
[6]
S.K. Srivastava,et al.
RADARSAT-1 image quality/five years of achievement
,
2001,
IGARSS 2001. Scanning the Present and Resolving the Future. Proceedings. IEEE 2001 International Geoscience and Remote Sensing Symposium (Cat. No.01CH37217).
[7]
A. Luscombe,et al.
The RADARSAT Synthetic Aperture Radar Development
,
1993
.
[8]
Kevin Murnaghan,et al.
RADARSAT-1 image quality/continuing success in extended mission
,
2002,
IEEE International Geoscience and Remote Sensing Symposium.
[9]
R. K. Hawkins,et al.
RADARSAT precision transponder
,
1997
.
[10]
T. I. Lukowski,et al.
Plans for RADARSAT image data calibration
,
1996
.
[11]
S.K. Srivastava,et al.
RADARSAT elevation antenna pattern determination
,
1997,
IGARSS'97. 1997 IEEE International Geoscience and Remote Sensing Symposium Proceedings. Remote Sensing - A Scientific Vision for Sustainable Development.