Effect of second-phase particle evolution in a twin-roll-casted Al-Mg-Si alloy on recrystallization texture and mechanical anisotropy

[1]  Yun-lai Deng,et al.  Microstructures and strengthening mechanisms of high Fe containing Al–Mg–Si–Mn–Fe alloys with Mg, Si and Mn modified , 2020 .

[2]  M. Zha,et al.  Effects of Mg contents on the microstructure evolution and Fe–bearing phase selection of Al–Mg–Si–Fe alloys under sub–rapid solidification , 2020 .

[3]  K. Matsuda,et al.  Effect of cooling rate on precipitation during homogenization cooling in excess Si type Al–Mg–Si alloy , 2020 .

[4]  J. Kuang,et al.  Heterogeneous microstructure-mediated ductile fracture of twin-roll cast Al–Mn strip , 2020 .

[5]  T. Jiang,et al.  Microcharacterization and mechanical performance of an Al-50Si alloy prepared using the sub-rapid solidification technique , 2020 .

[6]  M. Sedighi,et al.  The effect of temperature on the mechanical properties and forming limit diagram of aluminum strips fabricated by accumulative roll bonding process , 2020, Journal of Materials Research and Technology.

[7]  Di Wu,et al.  Effect of electromagnetic fields on microstructure and mechanical properties of sub-rapid solidification-processed Al–Mg–Si alloy during twin-roll casting , 2019, Materials Science and Engineering: A.

[8]  T. Carlberg,et al.  In-situ study of phase transformations during homogenization of 6060 and 6063 Al alloys , 2019, Journal of Physics and Chemistry of Solids.

[9]  P. Vullum,et al.  Effect of Mn and cooling rates on α-, β- and δ-Al–Fe–Si intermetallic phase formation in a secondary Al–Si alloy , 2019, Materialia.

[10]  Hyoung-Wook Kim,et al.  Deformation-induced center segregation in twin-roll cast high-Mg Al–Mg strips , 2018, Scripta Materialia.

[11]  L. Jia,et al.  Effect of cooling rate and Co content on the formation of Fe-rich intermetallics in hypoeutectic Al7Si0.3Mg alloy with 0.5%Fe , 2018 .

[12]  T. Carlberg,et al.  In-situ study of phase transformations during homogenization of 6005 and 6082 Al alloys , 2017 .

[13]  L. Zhuang,et al.  The formation of bimodal grain size distribution in Al-Mg-Si-Cu alloy and its effect on the formability , 2017 .

[14]  C. Kiminami,et al.  Predicting the Formation of Intermetallic Phases in the Al-Si-Fe System with Mn Additions , 2017 .

[15]  Qing Liu,et al.  Influence of pre-recovery on the subsequent recrystallization and mechanical properties of a twin-roll cast Al-Mn alloy , 2017 .

[16]  Jijie Wang,et al.  Effect of Fe, Si and Cooling Rate on the Formation of Fe- and Mn-rich Intermetallics in Al–5Mg–0.8Mn Alloy , 2016 .

[17]  L. Zhuang,et al.  The dependence of microstructure, texture evolution and mechanical properties of Al–Mg–Si–Cu alloy sheet on final cold rolling deformation , 2016 .

[18]  Y. Estrin,et al.  The influence of Mg/Si ratio and Cu content on the stretch formability of 6xxx aluminium alloys , 2016 .

[19]  L. Zhuang,et al.  The dependence of final microstructure, texture evolution and mechanical properties of Al–Mg–Si–Cu alloy sheets on the intermediate annealing , 2015 .

[20]  B. Mirzakhani,et al.  Combination of sever plastic deformation and precipitation hardening processes affecting the mechanical properties in Al–Mg–Si alloy , 2015 .

[21]  L. Kestens,et al.  Evolution of recrystallization textures in particle containing Al alloys after various rolling reductions: Experimental study and modeling , 2015 .

[22]  Tingju Li,et al.  Effects of ultrasonic treatment on the formation of iron-containing intermetallic compounds in Al-12%Si-2%Fe alloys , 2013 .

[23]  Y. Birol.  Optimization of homogenization for a low alloyed AlMgSi alloy , 2013 .

[24]  J. Hirsch,et al.  Superior light metals by texture engineering: Optimized aluminum and magnesium alloys for automotive applications , 2013 .

[25]  Y. Birol.  Effect of cooling rate on precipitation during homogenization cooling in an excess silicon AlMgSi alloy , 2012 .

[26]  Yonghao Zhang,et al.  Three-dimensional investigation of recrystallization nucleation in a particle-containing Al alloy , 2012 .

[27]  Y. Birol.  Homogenization of EN AW 6005A Alloy for Improved Extrudability , 2012, Metallurgical and Materials Transactions A.

[28]  L. Kestens,et al.  Deformation, recrystallization and plastic anisotropy of asymmetrically rolled aluminum sheets , 2010 .

[29]  L. Kestens,et al.  Effect of particles on texture banding in an aluminium alloy , 2010 .

[30]  L. Kestens,et al.  Microstructural and crystallographic aspects of conventional and asymmetric rolling processes , 2008 .

[31]  M. Ferrante,et al.  Prediction of rheological behaviour and segregation susceptibility of semi-solid aluminium-silicon alloys by a simple back extrusion test , 2005 .

[32]  Y. Birol.  Pre-straining to improve the bake hardening response of a twin-roll cast Al¿Mg¿Si alloy , 2005 .

[33]  Tatsuo Sato,et al.  Influence of Li addition on intermetallic compound morphologies in Al–Si–Cu–Fe cast alloys , 2004 .

[34]  Y. Birol.  The effect of homogenization practice on the microstructure of AA6063 billets , 2004 .

[35]  Olaf Engler,et al.  Texture control by thermomechanical processing of AA6xxx Al–Mg–Si sheet alloys for automotive applications—a review , 2002 .

[36]  S. Zając,et al.  Influence of Cooling after Homogenisation and Reheating to Extrusion on Extrudability and Final Properties of AA 6063 and AA6082 Alloys , 2002 .

[37]  R. Doherty.  Recrystallization and texture , 1997 .

[38]  J. Hirsch,et al.  Recrystallization Textures and Plastic Anisotropy in Al-Mg-Si Sheet Alloys , 1996 .

[39]  O. Engler,et al.  Mechanisms of recrystallization texture formation in aluminium alloys , 1992 .