MEMS microphones with narrow sensitivity distribution

Abstract This paper presents a method for calibrating MEMS microphones after the fabrication process. This allows compensating process tolerances and packaging stress of the capacitive membrane-backplate system. A programmable MEMS microphone with variable bias voltage and variable gain was developed and fabricated. The sensitivity of this microphone can be adjusted within a range of 11 dB. The adjustability was used to trim the sensitivity towards a specified value and to reduce the variation of the sensitivity. In mass production a tight sensitivity of ±1 dB could be reached, for a specified sensitivity of −38 dBV/Pa @ 1 kHz. In addition the microphone signal to noise ratio was increased to values above 66 dB(A) by choosing high bias voltages and matching gain calibration. The relationship between bias supply voltage and the non-linear dynamics of a double backplate sensor is explained. The influence of programming on the sensitivity, noise, SNR, THD and frequency response was investigated.

[1]  Bertan Bakkaloglu,et al.  In situ tuning of a MEMS microphone using electrodeposited nanostructures , 2009 .

[2]  Jian Liu,et al.  NONLINEAR DYNAMICS OF A DUAL-BACKPLATE CAPACITIVE MEMS MICROPHONE , 2007 .

[3]  Ole Hansen,et al.  Micromachined double backplate differential capacitive microphone , 1999 .

[4]  Matthias Winter,et al.  Flip chip packaging for MEMS microphones , 2010 .

[5]  T. Brosnihan,et al.  A MEMS Condenser Microphone for Consumer Applications , 2006, 19th IEEE International Conference on Micro Electro Mechanical Systems.

[6]  Wolfgang Pahl,et al.  Flip-chip MEMS microphone package with small front-volume and large back-volume , 2015, 2015 European Microelectronics Packaging Conference (EMPC).

[7]  Ulrich Krumbein,et al.  The Infineon Silicon MEMS Microphone , 2013 .

[8]  Zhong-Hua Fu,et al.  Dual-microphone noise reduction for mobile phone application , 2013, 2013 IEEE International Conference on Acoustics, Speech and Signal Processing.

[9]  Gregor Feiertag,et al.  Packaging of MEMS microphones , 2009, Microtechnologies.

[10]  Helmut Seidel,et al.  Influence of a chip scale package on the frequency response of a MEMS microphone , 2010 .

[11]  Wouter Olthuis,et al.  A review of silicon microphones , 1994 .

[12]  M. Sheplak,et al.  Surface and bulk micromachined dual back-plate condenser microphone , 2005, 18th IEEE International Conference on Micro Electro Mechanical Systems, 2005. MEMS 2005..

[13]  Charles Ching-Hsiang Hsu,et al.  Neobit@ -High Reliable Logic Non-Volatile Memory (NVM) , 2004 .

[14]  Byung-Hun Kim,et al.  Acoustical-Thermal Noise in a Capacitive MEMS Microphone , 2015, IEEE Sensors Journal.

[15]  Ming-Chih Yew,et al.  A study of residual stress effects on CMOS-MEMS microphone technology , 2009, 2009 4th International Microsystems, Packaging, Assembly and Circuits Technology Conference.

[16]  Ulrich Krumbein,et al.  Design of a poly silicon MEMS microphone for high signal-to-noise ratio , 2013, 2013 Proceedings of the European Solid-State Device Research Conference (ESSDERC).

[17]  R.S.C. Wang,et al.  Neobit/sup /spl reg// - high reliable logic non-volatile memory (NVM) , 2004, Proceedings of the 11th International Symposium on the Physical and Failure Analysis of Integrated Circuits. IPFA 2004 (IEEE Cat. No.04TH8743).

[18]  P. Rombach,et al.  The first low voltage, low noise differential silicon microphone, technology development and measurement results , 2001, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[19]  Gregor Feiertag,et al.  A Novel Method for Reducing the Sensitivity Deviation of MEMS Microphones by Programming , 2015 .

[20]  C. Chuang,et al.  Parametric study of flip-chip packaging for an MEMS device with diaphragm , 2010, 2010 Symposium on Design Test Integration and Packaging of MEMS/MOEMS (DTIP).

[21]  O. Rusanen,et al.  Adhesives as a thermomechanical stress source-comparing silicones to epoxies , 1998, Proceedings of 3rd International Conference on Adhesive Joining and Coating Technology in Electronics Manufacturing 1998 (Cat. No.98EX180).