Simulating the effect of temperature elevation on clamping force requirements during rigid-tool Liquid Composite Moulding processes

Abstract Moulds used for rigid-tool Liquid Composite Moulding (LCM) processes, namely Resin Transfer Moulding (RTM) and Compression RTM, are often subjected to large internal forces which originate due to resin injection and from the compaction of fibre reinforcements. Appropriate clamping equipment (e.g. press or perimeter clamps) is necessary to equilibrate these forces. An optimal selection (or design) of such clamping equipment calls for an accurate prediction of the tooling forces generated. This work aims to introduce a comprehensive numerical scheme which addresses this issue, including the case of non-isothermal mould filling. A hybrid Finite Element/Finite Difference (FE/FD) methodology is utilised for solving the coupled flow/energy/species equations. A new fibre compaction model, developed in order to reduce computational complexity while maintaining solution accuracy, is implemented into the simulation algorithm. The force predictions obtained for a planar axisymmetric part reveal that the chosen combination of mould and resin temperatures, together with other process variables, plays a crucial role in allowing fast fill times while keeping setup costs low.

[1]  Coupled Non-Conforming Finite Element and Finite Difference Approximation Based on Laminate Extrapolation to Simulate Liquid Composite Molding Processes. Part II: Non-Isothermal Filling and Curing , 2007 .

[2]  Piaras Kelly,et al.  Viscoelastic response of dry and wet fibrous materials during infusion processes , 2006 .

[3]  Chih-Yuan Chang,et al.  Simulation of Mold Filling in Simultaneous Resin Injection/Compression Molding , 2006 .

[4]  L. J. Lee,et al.  Mold filling and curing analysis in liquid composite molding , 1993 .

[5]  Musa R. Kamal,et al.  Kinetics and thermal characterization of thermoset cure , 1973 .

[6]  Piaras Kelly,et al.  Measurements of normal stress distributions experienced by rigid liquid composite moulding tools , 2009 .

[7]  T. Hughes,et al.  Streamline upwind/Petrov-Galerkin formulations for convection dominated flows with particular emphasis on the incompressible Navier-Stokes equations , 1990 .

[8]  Kumar K. Tamma,et al.  Non-isothermal ‘2-D flow/3-D thermal’ developments encompassing process modelling of composites: flow/thermal/cure formulations and validations , 1999 .

[9]  Bart Verleye,et al.  Simulation and experimental validation of force controlled compression resin transfer molding , 2011 .

[10]  Simon Bickerton,et al.  Modeling forces generated within rigid liquid composite molding tools. Part B: Numerical analysis , 2007 .

[11]  M. V. Bruschke,et al.  A finite element/control volume approach to mold filling in anisotropic porous media , 1990 .

[12]  Jose M. Castro,et al.  A note on the paper viscosity changes during urethane polymerization with phase separation , 1984 .

[13]  Piaras Kelly,et al.  A comprehensive filling and tooling force analysis for rigid mould LCM processes , 2009 .

[14]  F. Trochu,et al.  Numerical analysis of the resin transfer molding process by the finite element method , 1993 .

[15]  Piaras Kelly.  A Fibre Compaction Model for Liquid Composite Moulding , 2007 .

[16]  S. Bickerton,et al.  Modeling forces generated within rigid liquid composite molding tools. Part A: Experimental study , 2007 .

[17]  W. Young.  Development of a Helicopter Landing Gear Prototype using Resin Infusion Molding , 2009 .

[18]  Bart Verleye,et al.  Prediction and experimental verification of normal stress distributions on mould tools during Liquid Composite Moulding , 2012 .

[19]  Ming-Shyan Huang,et al.  Simulation of injection-compression mold-filling process , 1998 .

[20]  P. Kelly,et al.  A viscoelastic model for the compaction of fibrous materials , 2011 .

[21]  H. Tan,et al.  Numerical simulation of reactive flow in liquid composite molding using flux-corrected transport (FCT) based finite element/control volume (FE/CV) method , 2010 .