A Novel Aerial Manipulation Design, Modelling and Control for Geometric CoM Compensation

This paper presents the design and modelling of a new Aerial manipulating system, that resolve a displacement of centre of gravity of the whole system with a mechanical device. A prismatic joint between the multirotor and a robotic arm is introduced to make a centre of mass as close as to the geometric centre of the whole system. This paper details also the geometric and dynamic modelling of a coupled system with a Lagrange formalism and control law with a Closed Loop Inverse Kinematic Algorithm (CLIKA). This dynamic inverse control is validated in a Simulink environment showing the efficiency of our approach.

[1]  Lorenzo Marconi,et al.  Developing an Aerial Manipulator Prototype: Physical Interaction with the Environment , 2014, IEEE Robotics & Automation Magazine.

[2]  Kamel Bouzgou,et al.  Singularity Analysis and Illustration of Inverse Kinematic Solutions of 6 DOF Fanuc 200IC Robot in Virtual Environment , 2014 .

[3]  G. Oriolo,et al.  Robotics: Modelling, Planning and Control , 2008 .

[4]  David Hyunchul Shim,et al.  Development of a Vision-enabled Aerial Manipulator using a Parallel Robot , 2016 .

[5]  Vincenzo Lippiello,et al.  Cartesian Impedance Control of a UAV with a Robotic Arm , 2012, SyRoCo.

[6]  Bülent İrfanoğlu,et al.  Disturbance Rejection Control of a Quadrotor Equipped with a 2 DOF Manipulator , 2015 .

[7]  Konstantin Kondak,et al.  Closed-Loop Behavior of an Autonomous Helicopter Equipped with a Robotic Arm for Aerial Manipulation Tasks , 2013 .

[8]  Matko Orsag,et al.  Dynamic stability of a mobile manipulating unmanned aerial vehicle , 2013, 2013 IEEE International Conference on Robotics and Automation.

[9]  G. Heredia,et al.  Aerial manipulator with a compliant arm for bridge inspection , 2017, 2017 International Conference on Unmanned Aircraft Systems (ICUAS).

[10]  Kamel Bouzgou,et al.  Geometric modeling and singularity of 6 DOF Fanuc 200IC robot , 2014, Fourth edition of the International Conference on the Innovative Computing Technology (INTECH 2014).

[11]  Vincenzo Lippiello,et al.  Exploiting redundancy in Cartesian impedance control of UAVs equipped with a robotic arm , 2012, 2012 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[12]  Giuseppe Muscio,et al.  Control of quadrotor aerial vehicles equipped with a robotic arm , 2013, 21st Mediterranean Conference on Control and Automation.

[13]  Aníbal Ollero,et al.  A multilayer control for multirotor UAVs equipped with a servo robot arm , 2015, 2015 IEEE International Conference on Robotics and Automation (ICRA).

[14]  Anuradha M. Annaswamy,et al.  Controlled Manipulation with Multiple Quadrotors , 2011 .

[15]  Paul Y. Oh,et al.  A parallel manipulator for mobile manipulating UAVs , 2015, 2015 IEEE International Conference on Technologies for Practical Robot Applications (TePRA).

[16]  Stefano Stramigioli,et al.  Exploiting the dynamics of a robotic manipulator for control of UAVs , 2014, 2014 IEEE International Conference on Robotics and Automation (ICRA).

[17]  Bruno Vilhena Adorno,et al.  WHOLE-BODY MODELING AND CONTROL OF AN UNMANNED AERIAL MANIPULATOR , 2015 .

[18]  Matko Orsag,et al.  Modeling and Control of MM-UAV: Mobile Manipulating Unmanned Aerial Vehicle , 2013, J. Intell. Robotic Syst..

[19]  Paul Y. Oh,et al.  Design and Control of a Hyper-Redundant Manipulator for Mobile Manipulating Unmanned Aerial Vehicles , 2014, J. Intell. Robotic Syst..

[20]  Aaron M. Dollar,et al.  Design Optimization of a Prismatic-Revolute-Revolute Joint Hand for Grasping From Unconstrained Vehicles , 2017 .

[21]  Kamel Bouzgou,et al.  Virtual reality simulation and singularity analysis of 3-RRR translational parallel robot , 2015, Fifth International Conference on the Innovative Computing Technology (INTECH 2015).

[22]  R. Lozano,et al.  Task-based control of a multirotor miniature aerial vehicle having an onboard manipulator , 2014, 2014 International Conference on Unmanned Aircraft Systems (ICUAS).

[23]  Bouzgou Kamel,et al.  Dynamic modeling, simulation and PID controller of unmanned aerial vehicle UAV , 2017, 2017 Seventh International Conference on Innovative Computing Technology (INTECH).

[24]  Konstantin Kondak,et al.  First analysis and experiments in aerial manipulation using fully actuated redundant robot arm , 2013, 2013 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[25]  Dennis S. Bernstein,et al.  Adaptive control of a quadrotor UAV transporting a cable-suspended load with unknown mass , 2014, 53rd IEEE Conference on Decision and Control.

[26]  Seungwon Choi,et al.  Aerial manipulation using a quadrotor with a two DOF robotic arm , 2013, 2013 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[27]  Joe Woong Yeol,et al.  Design and Analysis of a Multiple Tentacle System for Mobile Manipulation in Micro Aerial Vehicles , 2017 .