An experimental study of condensation heat transfer inside a mini-channel with a new measurement technique

Abstract New experimental techniques were developed to measure the in-tube condensation heat transfer coefficient. In this study, very low heat dissipation rates such as several watts from the mini-channel could be estimated and low mass flow rates below the 0.2 kg/h could be measured with reasonable uncertainties. To the authors’ knowledge, these techniques provide a unique experimental apparatus for measuring the condensation heat transfer coefficients inside the sub-millimeter hydraulic diameter single channels. By careful design and construction of the experimental apparatus, the characteristics of the local heat transfer and pressure drop were experimentally investigated using the condensing R134a two-phase flow, in a horizontal single round tube, with an inner diameter of 0.691 mm. Tests were performed for a mass flux of 100–600 kg/m2s, a heat flux of 5–20 kW/m2, and a saturation temperature of 40 °C. The experimental data of the Nusselt number and two-phase frictional pressure gradient are presented and compared with the existing correlations.

[2]  M. Shah.  A general correlation for heat transfer during film condensation inside pipes , 1979 .

[3]  S. Koyama,et al.  Condensation of Refrigerant in a Multi-Port Channel , 2003 .

[4]  Peter B. Whalley,et al.  Boiling, Condensation, and Gas-Liquid Flow , 1987 .

[5]  Ralph L. Webb,et al.  A New Equivalent Reynolds Number Model for Condensation in Smooth Tubes , 1998 .

[6]  J. Thome,et al.  Convective Boiling and Condensation , 1972 .

[7]  L. Friedel.  Improved Friction Pressure Drop Correlation for Horizontal and Vertical Two-Phase Pipe Flow , 1979 .

[8]  J. P. Holman,et al.  Experimental methods for engineers , 1971 .

[9]  Tsing-Fa Lin,et al.  Evaporation heat transfer and pressure drop of refrigerant R-134a in a small pipe , 1998 .

[10]  Monte Keith Dobson,et al.  Heat Transfer and Flow Regimes During Condensation in Horizontal Tubes , 1994 .

[11]  W. Wang,et al.  A condensation heat transfer correlation for millimeter-scale tubing with flow regime transition , 2002 .

[12]  Srinivas Garimella,et al.  Condensation Flow Mechanisms in Microchannels: Basis for Pressure Drop and Heat Transfer Models , 2004 .

[13]  김종수.  알루미늄 평편 압축관내 R-134a의 응축열전달 및 압력손실 ( Condensing Heat Transfer and Pressure Drop of HFC-134a inside a Flat Extruded Aluminum Tube ) , 1996 .

[14]  Satish G. Kandlikar,et al.  Fundamental issues related to flow boiling in minichannels and microchannels , 2002 .

[15]  R. Webb,et al.  Condensation of R-12 in small hydraulic diameter extruded aluminum tubes with and without micro-fins , 1996 .

[16]  Mark O. McLinden,et al.  NIST Thermodynamic and Transport Properties of Refrigerants and Refrigerant Mixtures-REFPROP , 1998 .

[17]  Zeng-Yuan Guo,et al.  Size effect on microscale single-phase flow and heat transfer , 2002 .

[18]  Satish G. Kandlikar,et al.  Microchannels and Minichannels: History, Terminology, Classification and Current Research Needs , 2003 .

[19]  M. Heun,et al.  Performance and Optimization of Microchannel Condensers , 1995 .

[20]  R. Webb,et al.  Effect of Hydraulic Diameter on Condensation of R-134A in Flat, Extruded Aluminum Tubes , 2001 .