Computational fluid dynamic and thermal analysis of Lithium-ion battery pack with air cooling

A battery pack is produced by connecting the cells in series and/or in parallel to provide the necessary power for electric vehicles (EVs). Those parameters affecting cost and reliability of the EVs, including cycle life, capacity, durability and warranty are highly dependent on the thermal management system. In this work, computational fluid dynamic analysis is performed to investigate the air cooling system for a 38,120 cell battery pack. The battery pack contained 24 pieces of 38,120 cells, copper bus bars, intake and exhaust plenum and holding plates with venting holes. Heat generated by the cell during charging is measured using an accelerating rate calorimeter. Thermal performances of the battery pack were analyzed with various mass flow rates of cooling air using steady state simulation. The correlation between Nu number and Re number were deduced from the numerical modeling results and compared with literature. Additionally, an experimental testing of the battery pack at different charging rates is conducted to validate the correlation. This method provides a simple way to estimate thermal performance of the battery pack when the battery pack is large and full transient simulation is not viable.

[1]  Binggang Cao,et al.  Three-dimensional thermal finite element modeling of lithium-ion battery in thermal abuse application , 2010 .

[2]  Noam Lior,et al.  Heat transfer from a cylinder in axial turbulent flows , 2005 .

[3]  Gi‐Heon Kim,et al.  A three-dimensional thermal abuse model for lithium-ion cells , 2007 .

[4]  Sungjin Park,et al.  Battery cell arrangement and heat transfer fluid effects on the parasitic power consumption and the cell temperature distribution in a hybrid electric vehicle , 2013 .

[5]  Kiari Goni Boulama,et al.  Flow and performance characteristics of an Allison 250 gas turbine S-shaped diffuser: Effects of geometry variations , 2013 .

[6]  Siaw Kiang Chou,et al.  Ultra-thin minichannel LCP for EV battery thermal management , 2014 .

[7]  Lip Huat Saw,et al.  Electro-thermal characterization of Lithium Iron Phosphate cell with equivalent circuit modeling , 2014 .

[8]  Zhonghao Rao,et al.  A review of power battery thermal energy management , 2011 .

[9]  T. Coakley,et al.  Turbulence Modeling Validation, Testing, and Development , 1997 .

[10]  Zhengguo Zhang,et al.  Experimental and numerical investigation of the application of phase change materials in a simulative power batteries thermal management system , 2014 .

[11]  Weeratunge Malalasekera,et al.  An introduction to computational fluid dynamics - the finite volume method , 2007 .

[12]  D. Jeon,et al.  Thermal modeling of cylindrical lithium ion battery during discharge cycle , 2011 .

[13]  Joeri Van Mierlo,et al.  Standardization Work for BEV and HEV Applications: Critical Appraisal of Recent Traction Battery Documents , 2012 .

[14]  Anthony Jarrett,et al.  Design optimization of electric vehicle battery cooling plates for thermal performance , 2011 .

[15]  Sun Wook Kim,et al.  Development of battery management system for nickel–metal hydride batteries in electric vehicle applications , 2002 .

[16]  Gerhardus Swanepoel,et al.  Thermal management of hybrid electrical vehicles using heat pipes , 2001 .

[17]  A. Pesaran,et al.  Thermal Performance of EV and HEV Battery Modules and Packs , 1997 .

[18]  Chaoyang Wang,et al.  Control oriented 1D electrochemical model of lithium ion battery , 2007 .

[19]  Lip Huat Saw,et al.  Electro-thermal analysis and integration issues of lithium ion battery for electric vehicles , 2014 .

[20]  J. Selman,et al.  Active (air-cooled) vs. passive (phase change material) thermal management of high power lithium-ion packs: Limitation of temperature rise and uniformity of temperature distribution , 2008 .

[21]  G. H. Miller,et al.  Thermal Management of Hybrid Vehicle Battery Systems , 2009 .

[22]  Zhengguo Zhang,et al.  A hybrid thermal management system for lithium ion batteries combining phase change materials with forced-air cooling , 2015 .

[23]  Debashis Ghosh,et al.  Design and CFD Simulation of a Battery Module for a Hybrid Electric Vehicle Battery Pack , 2009 .

[24]  Hao Mu,et al.  A novel multi-model probability battery state of charge estimation approach for electric vehicles using H-infinity algorithm , 2016 .

[25]  Mao-Sung Wu,et al.  Heat dissipation design for lithium-ion batteries , 2002 .

[26]  Arun S. Mujumdar,et al.  Thermal–electrochemical model for passive thermal management of a spiral-wound lithium-ion battery , 2012 .

[27]  Bor Yann Liaw,et al.  The use of computer simulation in the evaluation of electric vehicle batteries , 1998 .

[28]  Chaoyang Wang,et al.  Power and thermal characterization of a lithium-ion battery pack for hybrid-electric vehicles , 2006 .

[29]  Anthony Jarrett,et al.  Influence of operating conditions on the optimum design of electric vehicle battery cooling plates , 2014 .

[30]  A. Pesaran.  Battery Thermal Management in EVs and HEVs : Issues and Solutions , 2001 .

[31]  Xiaosong Hu,et al.  Arrhenius Equation-Based Cell-Health Assessment: Application to Thermal Energy Management Design of a HEV NiMH Battery Pack , 2013 .

[32]  Debashis Ghosh,et al.  Full Hybrid Electrical Vehicle Battery Pack System Design, CFD Simulation and Testing , 2010 .

[33]  Zonghai Chen,et al.  A new model for State-of-Charge (SOC) estimation for high-power Li-ion batteries , 2013 .

[34]  Yonghuang Ye,et al.  Electrochemical–thermal analysis of 18650 Lithium Iron Phosphate cell , 2013 .

[35]  F. Menter,et al.  Ten Years of Industrial Experience with the SST Turbulence Model , 2003 .

[36]  E. Sparrow,et al.  Flow separation in a diverging conical duct: Effect of Reynolds number and divergence angle , 2009 .

[37]  Terukazu Ota,et al.  Heat Transfer in an Axisymmetric Separated and Reattached Flow Over a Longitudinal Blunt Circular Cylinder , 1977 .

[38]  R. Mahamud,et al.  Reciprocating air flow for Li-ion battery thermal management to improve temperature uniformity , 2011 .

[39]  Seunghun Jung,et al.  Multi-dimensional modeling of large-scale lithium-ion batteries , 2014 .

[40]  Tsutomu Ohzuku,et al.  An overview of positive-electrode materials for advanced lithium-ion batteries , 2007 .

[41]  M. Muramatsu,et al.  Accurate and versatile simulation of transient voltage profile of lithium-ion secondary battery employing internal equivalent electric circuit , 2015 .

[42]  Ahmad Pesaran,et al.  Battery thermal models for hybrid vehicle simulations , 2002 .

[43]  Zhonghao Rao,et al.  Simulation and experiment of thermal energy management with phase change material for ageing LiFePO4 power battery , 2011 .

[44]  Ephraim M Sparrow,et al.  Local and average heat transfer characteristics for a disk situated perpendicular to a uniform flow , 1985 .

[45]  Robert J. Moffat,et al.  Describing the Uncertainties in Experimental Results , 1988 .

[46]  A. London,et al.  Compact heat exchangers , 1960 .

[47]  N. Omar,et al.  Rechargeable Energy Storage Systems for Plug-in Hybrid Electric Vehicles—Assessment of Electrical Characteristics , 2012 .

[48]  Isak Kotcioglu,et al.  Optimum design parameters of a heat exchanger , 2005 .

[49]  Ahmad Pesaran,et al.  Thermal Management of Batteries in Advanced Vehicles Using Phase-Change Materials (Presentation) , 2007 .