A simplified method to determine the 3D orientation of an injection molded fiber‐filled polymer

In short-fiber reinforced composites, it is widely accepted that the fiber orientation plays an important role on their overall physical and thermomechanical properties. To predict the properties of such composite materials, a full 3D fiber orientation characterization is required. A variety of destructive and nondestructive techniques have been developed, but all the methods have the same common point that they are very tedious and time consuming. Knowing that the fiber orientation induced by the flow remains mainly in the flow plane, an easier method has been performed for injection molded fiber-filled polymers. It is based on the simple 2D SEM image analysis of a specific 45°-oblique section plane. Then, the indetermination of fiber orientation from an ellipse mark analysis does not exist anymore. This novelty also turns out to be much more accurate. To achieve measurements over large composite samples, the method has been fully automated. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers

[1]  Pierre Gilormini,et al.  Comparison of several closure approximations for evaluating the thermoelastic properties of an injection molded short-fiber composite , 2007 .

[2]  Ignace Verpoest,et al.  Micro-CT characterization of variability in 3D textile architecture , 2005 .

[3]  M. Vincent,et al.  Description and modeling of fiber orientation in injection molding of fiber reinforced thermoplastics , 2005 .

[4]  Jianxiang Wang,et al.  Prediction of the overall moduli of layered silicate-reinforced nanocomposites—part I: basic theory and formulas , 2004 .

[5]  F. Schmidt,et al.  Voids in short fibre-reinforced injection-moulded parts: density control vs. mass control , 2003 .

[6]  P. Hine,et al.  Orientation Averaging for Stiffness and Thermal Expansion of Short Fiber Composites , 2002 .

[7]  Michel Vincent,et al.  Fibre-orientation measurements in short-glass-fibre composites—II: a quantitative error estimate of the 2D image analysis technique , 2001 .

[8]  C. Eberhardt,et al.  Fibre-orientation measurements in short-glass-fibre composites. Part I: automated, high-angular-resolution measurement by confocal microscopy , 2001 .

[9]  G. Zak,et al.  Estimation of Three-Dimensional Fibre-Orientation Distribution in Short-Fibre Composites by a Two-Section Method , 2001 .

[10]  M. Dunn,et al.  Micromechanically-based acoustic characterization of the fiber orientation distribution function of morphologically textured short-fiber composites: prediction of thermomechanical and physical properties , 2000 .

[11]  B. Mlekusch,et al.  Thermoelastic properties of short-fibre-reinforced thermoplastics , 1999 .

[12]  Charles L. Tucker,et al.  Stiffness Predictions for Unidirectional Short-Fiber Composites: Review and Evaluation , 1999 .

[13]  B. Mlekusch,et al.  Fibre orientation in short-fibre-reinforced thermoplastics I. Contrast enhancement for image analysis , 1999 .

[14]  W. Blumenthal,et al.  Determination of Non-Symmetric 3-D Fiber-Orientation Distribution and Average Fiber Length in Short-Fiber Composites , 1997 .

[15]  L. Avérous,et al.  Evolution of the three-dimensional orientation distribution of glass fibers in injected isotactic polypropylene , 1997 .

[16]  A. Meunier,et al.  Application of scanning acoustic microscopy to polymeric materials , 1994 .

[17]  L. K. Jain,et al.  Effect of fiber orientation on the fracture toughness of brittle matrix composites , 1992 .

[18]  Charles L. Tucker,et al.  Stereological measurement and error estimates for three-dimensional fiber orientation , 1992 .

[19]  B. Möginger,et al.  Determination of the weighting function g(βi,r,vf) for fibre orientation analysis of short fibre-reinforced composites , 1991 .

[20]  R. Bailey,et al.  Fibre Orientation Mechanisms for Injection Molding of Long Fibre Composites , 1991 .

[21]  Musa R. Kamal,et al.  The effect of processing variables on microstructure of injection molded short fiber reinforced polypropylene composites , 1989 .

[22]  James L White,et al.  Wide angle X-ray diffraction investigations of orientation of chopped fibers in fabricated thermoplastic parts† , 1988 .

[23]  Peter Eyerer,et al.  Measuring spatial orientation of short fiber reinforced thermoplastics by image analysis , 1988 .

[24]  Suresh G. Advani,et al.  The Use of Tensors to Describe and Predict Fiber Orientation in Short Fiber Composites , 1987 .

[25]  M. W. Darlington,et al.  Fibre orientation distribution in short fibre reinforced plastics , 1975 .

[26]  N. C. Davidson,et al.  A novel technique for determining the 3D spatial distribution of glass fibres in polymer composites , 1995 .

[27]  S. Yurgartis.  Techniques for the quantification of composite mesostructure , 1995 .

[28]  Peter Hine,et al.  Modelling of the elastic properties of fibre reinforced composites. I: Orientation measurement , 1993 .

[29]  K. Urabe,et al.  A nondestructive testing method of fiber orientation by microwave , 1987 .

[30]  S. W. Yurgartis.  Measurement of small angle fiber misalignments in continuous fiber composites , 1987 .

[31]  M. Folkes,et al.  A rapid technique for observing fibre orientation in carbon fibre-reinforced thermoplastics , 1985 .

[32]  P. Parrini,et al.  A NEW TECHNIQUE FOR THE MEASUREMENT OF GLASS FIBER ORIENTATION IN COMPOSITE MATERIALS , 1980 .