Automatic yield-line analysis of slabs using discontinuity layout optimization

The yield-line method of analysis is a long established and extremely effective means of estimating the maximum load sustainable by a slab or plate. However, although numerous attempts to automate the process of directly identifying the critical pattern of yield-lines have been made over the past few decades, to date none has proved capable of reliably analysing slabs of arbitrary geometry. Here, it is demonstrated that the discontinuity layout optimization (DLO) procedure can successfully be applied to such problems. The procedure involves discretization of the problem using nodes inter-connected by potential yield-line discontinuities, with the critical layout of these then identified using linear programming. The procedure is applied to various benchmark problems, demonstrating that highly accurate solutions can be obtained, and showing that DLO provides a truly systematic means of directly and reliably automatically identifying yield-line patterns. Finally, since the critical yield-line patterns for many problems are found to be quite complex in form, a means of automatically simplifying these is presented.

[1]  Robert J. Vanderbei,et al.  Linear Programming: Foundations and Extensions , 1998, Kluwer international series in operations research and management service.

[2]  H. Chan,et al.  The collapse load of reinforced concrete plate , 1972 .

[3]  Campbell R. Middleton,et al.  Closely correlating lower and upper bound plastic analysis of real slabs , 2013 .

[4]  Mogens Peter Nielsen,et al.  Limit Analysis and Concrete Plasticity , 2010 .

[5]  P. E. Regan,et al.  Limit State Design of Structural Concrete , 1973 .

[6]  Matthew Gilbert,et al.  Optimum structure to carry a uniform load between pinned supports , 2010 .

[7]  G. Saxcé,et al.  Plastic Limit Analysis of Plates, Shells and Disks , 2011 .

[8]  Arne Hillerborg.  Strip Method of Design , 1976 .

[9]  A. A. Gvozdev.  The determination of the value of the collapse load for statically indeterminate systems undergoing plastic deformation , 1960 .

[10]  K. V. Balasubramanyam,et al.  Yield‐Line Analysis by Linear Programming , 1988 .

[11]  E. Anderheggen,et al.  Finite element limit analysis using linear programming , 1972 .

[12]  Werner Wagner,et al.  Systematic prediction of yield-line configurations for arbitrary polygonal plates , 2008 .

[13]  Kristian Krabbenhoft,et al.  A general non‐linear optimization algorithm for lower bound limit analysis , 2003 .

[14]  E. W. Parkes,et al.  Joints in optimum frameworks , 1975 .

[15]  S. R. Denton.  Compatibility requirements for yield-line mechanisms , 2001 .

[16]  M. Gilbert,et al.  Layout optimization of large‐scale pin‐jointed frames , 2003 .

[17]  E. A. W. Maunder,et al.  Equilibrium models for lower bound limit analyses of reinforced concrete slabs , 2012 .

[18]  Matthew Gilbert,et al.  Limit analysis of plates and slabs using a meshless equilibrium formulation , 2010 .

[19]  J Munro,et al.  YIELD LINE METHOD BY FINITE ELEMENTS AND LINEAR PROGRAMMING , 1978 .

[20]  L A Clark.  CONCRETE BRIDGE ASSESSMENT , 1997 .

[21]  Poul Colberg Olsen.  The influence of the linearisation of the yield surface on the load-bearing capacity of reinforced concrete slabs , 1998 .

[22]  David Johnson.  Yield-line analysis by sequential linear programming , 1995 .

[23]  S. Sloan,et al.  Formulation and solution of some plasticity problems as conic programs , 2007 .

[24]  Andrew Mark Jackson,et al.  Modelling the collapse behaviour of reinforced concrete slabs , 2011 .

[25]  冈上拓己.  Data Processing system and method , 2001 .

[26]  Matthew Gilbert,et al.  Application of discontinuity layout optimization to plane plasticity problems , 2007, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[27]  David Johnson.  Collapse Analysis of Reinforced Concrete Slabs: Are the Up and Down Roads One and the Same? , 2006 .

[28]  D. Sloan,et al.  Computer-assisted generation of yield-line patterns for uniformly loaded isotropic slabs using an optimisation strategy , 1999 .

[29]  Knud Winstrup Johansen.  Yield-line theory , 1962 .

[30]  J. Bleyer,et al.  On the performance of non‐conforming finite elements for the upper bound limit analysis of plates , 2013 .

[31]  M. Save.  A consistent limit-analysis theory for reinforced concrete slabs , 1967 .

[32]  A. Michell.  LVIII. The limits of economy of material in frame-structures , 1904 .

[33]  Harvey J. Greenberg,et al.  Automatic design of optimal structures , 1964 .

[34]  E. N. Fox.  Limit analysis for plates: the exact solution for a clamped square plate of isotropic homogeneous material obeying the square yield criteron and loaded by uniform pressure , 1974, Philosophical Transactions of the Royal Society of London. Series A, Mathematical and Physical Sciences.

[35]  Robert V. Kohn,et al.  Hencky-Prandtl nets and constrained Michell trusses , 1983 .

[36]  Valentı´n Quintas,et al.  Two Main Methods for Yield Line Analysis of Slabs , 2003 .