Effects of weld profile and undercut on fatigue crack propagation life of thin-walled cruciform joint

Fatigue may occur in undercarriages and support systems of trailers, haymakers, graders and swing-ploughs made up of thin-walled tubular sections with wall thicknesses less than 4 mm. Little research has been done on the fatigue of thin-walled tubular sections below 4 mm thickness. The weld profile and weld undercut may affect the fatigue crack propagation life of welded joints especially for thin-walled sections. Numerical analysis of 2-dimensional non-load carrying thin-walled cruciform joints was performed to determine the effect of weld profile and weld undercut on fatigue crack propagation life under cyclic tensile loading. The cruciform joints analysed are made up of 3 mm thick plates, joined by fillet welds. The Boundary Element Analysis System Software (BEASY) is used, which uses fracture mechanics theory to carry out crack propagation analysis. The weld profiles and weld undercuts were measured from welded connections in thin-walled fillet welded sections. The measured weld profiles and undercut were used in the analysis. The results are compared with those of a similar study to determine the comparative reduction in fatigue crack propagation life between thin-walled cruciform joints (T=3 mm) and thicker walled cruciform joints (T=20 mm). This paper provides an understanding of the impact which weld toe undercut has on the fatigue crack propagation life of thin-walled cruciform joints. The presence of undercuts may reduce the benefits of the thickness effect in thin-walled joints of thicknesses less than 4 mm.

[1]  M. A. Wahab,et al.  The effect of undercut and residual stresses on fatigue behaviour of misaligned butt joints , 1996 .

[2]  Fidelis R Mashiri,et al.  Crack propagation analysis of welded thin-walled cruciform joint using boundary element method , 1997 .

[3]  Timothy Russell Gurney,et al.  Fatigue of Welded Structures , 1980 .

[4]  John Trevelyan.  Boundary elements for engineers: Theory and applications , 1994 .

[5]  A. S. J. Swamidas,et al.  Fatigue strength of fillet-welded cruciform joints , 1989 .

[6]  S. J. Maddox,et al.  Fatigue strength of welded structures , 1991 .

[7]  Jaap Wardenier,et al.  Hollow section joints , 1982 .

[8]  Peter W. Marshall.  Design of Welded Tubular Connections : Basis and Use of AWS Code Provisions(構造)(学位論文要旨) , 1990 .

[9]  Takeshi Mori,et al.  Fatigue strength of transverse single-sided fillet welded joints , 1997 .

[10]  R. Bell,et al.  The significance of weld toe undercuts in the fatigue of steel plate T-joints , 1989 .

[11]  Ian F. C. Smith,et al.  Fatigue crack growth in a fillet welded joint , 1983 .

[12]  G. C. Sih,et al.  A fracture criterion for three-dimensional crack problems , 1974 .

[13]  J. E. Henderson,et al.  Design guide for hollow structural section connections , 1992 .

[14]  Jaap Wardenier,et al.  New Guidelines for Fatigue Design of HSS Connections , 1996 .

[15]  A W Beeby,et al.  CONCISE EUROCODE FOR THE DESIGN OF CONCRETE BUILDINGS. BASED ON BSI PUBLICATION DD ENV 1992-1-1: 1992. EUROCODE 2: DESIGN OF CONCRETE STRUCTURES. PART 1: GENERAL RULES AND RULES FOR BUILDINGS , 1993 .

[16]  D. Rooke,et al.  The dual boundary element method: Effective implementation for crack problems , 1992 .

[17]  J L Grover.  THICKNESS, WELD PROFILE AND INITIAL FLAW CONSIDERATIONS FOR TUBULAR JOINTS , 1989 .

[18]  Muhammad Abdul Wahab,et al.  A theoretical study of the effect of weld geometry parameters on fatigue crack propagation life , 1995 .

[19]  J. Newman.  A crack opening stress equation for fatigue crack growth , 1984 .

[20]  Ohta Akihiko,et al.  Evaluation of effect of plate thickness on fatigue strength of butt welded joints by a test maintaining maximum stress at yield strength , 1990 .

[21]  F. Mashiri,et al.  Fatigue design of welded very thin-walled tube-to-plate joints using the classification method , 2000 .

[22]  M. H. Aliabadi,et al.  THREE-DIMENSIONAL CRACK GROWTH SIMULATION USING BEM , 1994 .

[23]  Takeshi Mori,et al.  Fatigue resistance of welded tubular joints using fracture mechanics approach , 1999 .