Dynamic calibration of force balances for impulse hypersonic facilities

Abstract.This paper analyzes different techniques for the calibration of force balances for use in short-duration impulse hypersonic facilities such as shock tunnels. The background to how deconvolution can be used to infer aerodynamic forces on models in impulse hypersonic wind tunnels is presented along with the theory behind the different calibration techniques. Four calibration techniques are applied to a single-component stress-wave force balance. Experiments in the T4 shock tunnel using the balance demonstrate the suitability of the different calibrations for force measurements in an impulse facility. Cross checks between the calibration techniques are used to check their ranges of validity. It is shown that the impulse response derived from tests in which the model and force balance are suspended from a fine wire and the wire cut agree well with impulse responses derived from calibrations made using an impact hammer. The suitability of the balance for measuring dynamic forces is demonstrated by showing that the drag force on a model follows the history of Pitot pressure in the test section in the tunnel shots.

[1]  Sean Tuttle,et al.  Drag measurements at Mach 5 using a stress wave force balance , 1995 .

[2]  Peter A. Jacobs,et al.  Use of Argon-Helium Driver-Gas Mixtures in the T4 Shock Tunnel , 1995 .

[3]  David J. Mee.  Uncertainty Analysis of Conditions in the Test Section of the T4 Shock Tunnel , 1993 .

[4]  David J. Mee,et al.  Dynamic strain measurement using piezoelectric polymer film , 1996 .

[5]  David J. Mee.  Dynamic calibration of force balances , 2002 .

[6]  William J.T. Daniel,et al.  Design, modelling and analysis of a six component force balance for hypervelocity wind tunnel testing , 2001 .

[7]  F. White.  Viscous Fluid Flow , 1974 .

[8]  Allan Paull.  A simple shock tunnel driver gas detector , 1996 .

[9]  S R Sanderson,et al.  Drag balance for hypervelocity impulse facilities , 1991 .

[10]  Geoffrey Ingram Taylor,et al.  The Air Pressure on a Cone Moving at High Speeds. II , 1933 .

[11]  K. W. Naumann,et al.  Millisecond aerodynamic force measurement with side-jet model in theISL shock tunnel , 1993 .

[12]  J. R. Moselle,et al.  Computer program for the numerical solution of nonequilibrium expansions of reacting gas mixtures , 1966 .

[13]  H. Grönig,et al.  A new principle for a short-duration six component balance , 1989 .

[14]  Rémy Prost,et al.  Discrete constrained iterative deconvolution algorithms with optimized rate of convergence , 1984 .

[15]  William J.T. Daniel,et al.  Finite element modelling of a three-component force balance for hypersonic flows , 1995 .

[16]  Kenneth A Skinner.  Mass spectrometry in shock tunnel experiments of hypersonic combustion , 1994 .

[17]  D. Royer,et al.  Elastic waves in solids : applications to signal processing , 1980 .

[18]  Paulo Sergio Varoto,et al.  Vibration Testing: Theory and Practice , 1995 .

[19]  Allan Paull,et al.  Experiments on supersonic combustion ramjet propulsion in a shock tunnel , 1995, Journal of Fluid Mechanics.

[20]  A. L. Smith,et al.  Drag measurements in a hypervelocity expansion tube , 1996 .

[21]  M. V. Joshi,et al.  Aerodynamic force measurements over missile configurations in IISc shock tunnel at M∞ = 5.5 , 1986 .

[22]  Leonard Bernstein,et al.  Force Measurements in Short-Duration Hypersonic Facilities , 1975 .

[23]  Mario Carbonaro.  Aerodynamic Force Measurements in the VKI Longshot Hypersonic Facility , 1993 .

[24]  Ernest O. Doebelin,et al.  Systems Modeling and Response: Theoretical and Experimental Approaches , 1980 .

[25]  William J.T. Daniel,et al.  Three-component force balance for flows of millisecond duration , 1996 .