Optimizing 13.5nm laser-produced tin plasma emission as a function of laser wavelength

Extreme ultraviolet lithography requires a light source at 13.5nm to match the proposed multilayer optics reflectivity. The impact of wavelength and power density on the ion distribution and electron temperature in a laser-produced plasma is calculated for Nd:YAG and CO2 lasers. A steady-state figure of merit, calculated to optimize emission as a function of laser wavelength, shows an increase with a CO2 laser. The influence of reduced electron density in the CO2 laser-produced plasma is considered in a one-dimensional radiation transport model, where a more than twofold increase in conversion efficiency over that attainable with the Nd:YAG is predicted.

[1]  K. V. Roberts,et al.  MEDUSA a one-dimensional laser fusion code , 1984 .

[2]  A. Cummings,et al.  Conversion efficiency of a laser-produced Sn plasma at 13.5 nm, simulated with a one-dimensional hydrodynamic model and treated as a multi-component blackbody , 2005 .

[3]  E. Alexov,et al.  Electromagnetic waves in the semiconductor plasma waveguide , 1989 .

[4]  T. Kawamura,et al.  Simulation of the EUV spectrum of Xe and Sn plasmas , 2004, IEEE Journal of Selected Topics in Quantum Electronics.

[5]  M. Klapisch,et al.  Unresolved transition arrays , 1988 .

[6]  Tatsuya Aota,et al.  Ultimate efficiency of extreme ultraviolet radiation from a laser-produced plasma. , 2005, Physical review letters.

[7]  A. Cummings,et al.  13.5 nm extreme ultraviolet emission from tin based laser produced plasma sources , 2006 .

[8]  A. Cummings,et al.  Tin based laser-produced plasma source development for EUVL , 2006 .

[9]  S. Rose,et al.  Simulation of X-ray line transfer in a cylindrically expanding plasma , 1997 .

[10]  Martin Richardson,et al.  Diagnostics for laser plasma EUV sources , 2005, International Congress on High-Speed Imaging and Photonics.

[11]  Shinsuke Fujioka,et al.  Characterization of extreme ultraviolet emission from laser-produced spherical tin plasma generated with multiple laser beams , 2005 .

[12]  X-ray plasma source design simulations. , 1993, Applied optics.

[13]  Hiroaki Nishimura,et al.  Characterization of density profile of laser-produced Sn plasma for 13.5nm extreme ultraviolet source , 2005 .

[14]  Hiroki Tanaka,et al.  Comparative study on emission characteristics of extreme ultraviolet radiation from CO2 and Nd:YAG laser-produced tin plasmas , 2005 .

[15]  A. Cummings,et al.  Opacity of neutral and low ion stages of Sn at the wavelength 13.5 nm used in extreme-ultraviolet lithography , 2005 .

[16]  Vivek Bakshi,et al.  EUV Sources for Lithography , 2006 .

[17]  D. Attwood.  Extreme Ultraviolet Light Sources for Semiconductor Manufacturing , 2004 .

[18]  R. D. Cowan,et al.  The Theory of Atomic Structure and Spectra , 1981 .

[19]  Luke McKinney,et al.  Optimizing an EUV source for 13.5 nm , 2004, SPIE Optics + Photonics.

[20]  M Richardson,et al.  New laser plasma source for extreme-ultraviolet lithography. , 1995, Applied optics.

[21]  J. Bauche,et al.  Asymmetry oflN+1−lNl′transition-array patterns in ionic spectra , 1984 .

[22]  A. Cummings,et al.  Simplified modeling of 13.5 nm unresolved transition array emission of a Sn plasma and comparison with experiment , 2005 .

[23]  D. Heading,et al.  Experimental and simulated profiles of the Al XIII Ly-α resonance line from a cylindrically expanding plasma , 1997 .

[24]  A. Cummings,et al.  Simplified calculation of nonlocal thermodynamic equilibrium excited state populations contributing to 13.5nm emission in a tin plasma , 2007 .

[25]  G. Tonon,et al.  X‐ray emission in laser‐produced plasmas , 1973 .

[26]  Hiroaki Nishimura,et al.  Characterization of extreme ultraviolet emission using the fourth harmonic of a Nd:YAG laser , 2005 .