On the development of direct metal laser sintering for rapid tooling

Abstract An iron based powder blend has been developed for rapid tooling using a direct laser sintering process. The powder consists of a mixture of different elements including Fe, C, Cu, Mo and Ni. High sintering activities were obtained by tailoring the powder characteristics and optimizing the chemical constituents. The manufacturing of complex-shaped parts is possible at rates of 6.75 cm 3 /h according to CAD data. The residual porosity is less than 5 vol.%. The bending strength is around 900 MPa and the artifact hardness is 490 HV30. To further improve the service life of tools, the processed parts are sintered again in a vacuum furnace at 1260 °C for 30 min. This enables to manufacture precision parts with the density around 7.7 g/cm 3 (sintering shrinkage is nearly zero). The dimensional accuracy of the sintered parts is improved by using a beam compensation technique that is integrated in the computer program of the laser sintering system. In this article the sintering behavior, mechanical properties, and microstructural features of the multi-component iron based powder are given and implications of the material for industrial applications are presented. A case study was performed to present the applicability of the material for rapid tooling.

[1]  David L. Bourell,et al.  Selective laser sintering of metals and ceramics , 1992 .

[2]  I. Chang,et al.  Selective laser sintering of gas and water atomized high speed steel powders , 1999 .

[3]  I. Chang,et al.  Liquid phase sintering of M3/2 high speed steel by selective laser sintering , 1998 .

[4]  Y. Kathuria.  Microstructuring by selective laser sintering of metallic powder , 1999 .

[5]  Leong Kah Fai,et al.  Rapid Prototyping: Principles and Applications in Manufacturing , 2003 .

[6]  Abdolreza Simchi,et al.  Direct metal laser sintering : Material considerations and mechanisms of particle : Rand tooling of powdered metal parts , 2001 .

[7]  S. Yamazaki,et al.  Phenomenological Studies in Laser Cladding. Part I. Time-Resolved Measurements of the Absorptivity of Metal Powder , 1993 .

[8]  L. Pawlowski,et al.  Thick laser coatings: A review , 1999 .

[9]  Yu. V. Khlopkov,et al.  Absorptance of powder materials suitable for laser sintering , 2000 .

[10]  David L. Bourell,et al.  Direct laser fabrication of superalloy cermet abrasive turbine blade tips , 2000 .

[11]  F. Klocke,et al.  Rapid metal tooling , 1995 .

[12]  Jon Rigelsford.  Rapid Prototyping, Tooling and Manufacturing , 2003 .

[13]  Li Lu,et al.  Direct metal laser sintering for rapid tooling: processing and characterisation of EOS parts , 2001 .

[14]  APPROACHES TO PROCESSING METALS AND CERAMICS THROUGH THE LASER SCANNING OF POWDER BEDS - A REVIEW , 2001 .

[15]  I. Chang,et al.  Instability of scan tracks of selective laser sintering of high speed steel powder , 1999 .

[16]  Rémy Glardon,et al.  Optimization of powder layer density in selective laser sintering , 1999 .

[17]  Andreas Gebhardt,et al.  Rapid prototyping , 2003 .

[18]  G. K. Lewis,et al.  Practical considerations and capabilities for laser assisted direct metal deposition , 2000 .

[19]  Yasser A. Hosni,et al.  Rapid prototyping and tooling: A survey and applications , 1995 .

[20]  Jyoti Mazumder,et al.  Solidification behavior and microstructural evolution during laser beam—material interaction , 1998 .

[21]  L. Froyen,et al.  Effect of mechanical alloying on selective laser sintering of WC-9Co hard metal powder , 1998 .