Polymer deformation and filling modes during microembossing

This work investigates the initial stages of polymer deformation during hot embossing micro-manufacturing at processing temperatures near the glass transition temperature (Tg) of polymer films having sufficient thickness such that polymer flow is not supply limited. Several stages of polymer flow can be observed by employing stamp geometries of various widths and varying imprint conditions of time and temperature to modulate polymer viscosity. Experiments investigate conditions affecting cavity filling phenomena, including apparent polymer viscosity. Stamps with periodic ridges of height and width 4 µm and periodicity 30, 50 and 100 µm emboss trenches into polymethyl methacrylate films at Tg − 10 °C < Temboss < Tg + 20 °C. Imprint parameters of time, temperature and load are correlated with replicated polymer shape, height and imprinted area. Polymer replicates are measured by atomic force microscopy and inspected by scanning electron microscopy. Cavity size and the temperature dependence of polymer viscosity significantly influence the nature of polymer deformation in hot embossing micro-manufacturing and must be accounted for in rational process design.

[1]  Byung Kim,et al.  Simulation of the filling process in micro channels for polymeric materials , 2002 .

[2]  Chung-Yen Chao,et al.  Polymer microring resonators fabricated by nanoimprint technique , 2002 .

[3]  C. Willert,et al.  Three-dimensional particle imaging with a single camera , 1992 .

[4]  Clifford L. Henderson,et al.  Microsystems manufacturing via embossing of photodefinable thermally sacrificial materials , 2004, SPIE Advanced Lithography.

[6]  Kurt W. Koelling,et al.  Hot embossing in microfabrication. Part I: Experimental , 2002 .

[7]  R. Landel,et al.  The Temperature Dependence of Relaxation Mechanisms in Amorphous Polymers and Other Glass-Forming Liquids , 1955 .

[8]  Ye Pu,et al.  Holographic particle image velocimetry: from film to digital recording , 2004 .

[9]  Yoshihiko Hirai,et al.  Simulation and experimental study of polymer deformation in nanoimprint lithography , 2004 .

[10]  Kurt W. Koelling,et al.  Hot embossing in microfabrication. Part II: Rheological characterization and process analysis , 2002 .

[11]  Helmut Schift,et al.  Flow behaviour of thin polymer films used for hot embossing lithography , 2000 .

[12]  Stephen Y. Chou,et al.  Nanoscale silicon field effect transistors fabricated using imprint lithography , 1997 .

[13]  Dana Dabiri,et al.  A full three-dimensional characterization of defocusing digital particle image velocimetry , 2005 .

[14]  Liwei Lin,et al.  Microplastic embossing process: experimental and theoretical characterizations ☆ , 2002 .

[15]  William P King,et al.  Hot embossing for micropatterned cell substrates. , 2004, Biomaterials.

[16]  D. Khang,et al.  Wafer-scale sub-micron lithography , 1999 .

[17]  Stephen Y. Chou,et al.  Imprint lithography with sub-10 nm feature size and high throughput , 1997 .

[18]  Eung-Sug Lee,et al.  Flow behavior at the embossing stage of nanoimprint lithography , 2002 .

[19]  Hella-Christin Scheer,et al.  A contribution to the flow behaviour of thin polymer films during hot embossing lithography , 2001 .

[20]  Gwo-Bin Lee,et al.  Microfabricated plastic chips by hot embossing methods and their applications for DNA separation and detection , 2000, SPIE MOEMS-MEMS.