Fiber Length and Orientation in Long-Fiber Injection-Molded Thermoplastics — Part I: Modeling of Microstructure and Elastic Properties

This article develops a methodology to predict the elastic properties of long-fiber injection-molded thermoplastics (LFTs). The corrected experimental fiber length distribution and the predicted and experimental orientation distributions were used in modeling to compute the elastic properties of the composite. First, from the fiber length distribution (FLD) data in terms of number of fibers versus fiber length, the probability density functions were built and used in the computation. The two-parameter Weibull's distribution was also used to represent the actual FLD. Next, the Mori—Tanaka model that employs the Eshelby's equivalent inclusion method was applied to calculate the stiffness matrix of the aligned fiber composite containing the established FLD. The stiffness of the actual as-formed composite was then determined from the stiffness of the computed aligned fiber composite that was averaged over all possible orientations using the orientation averaging method. The methodology to predict the elastic properties of LFTs was validated via experimental verification of the longitudinal and transverse moduli determined for long glass fiber injection-molded polypropylene specimens. Finally, a sensitivity analysis was conducted to determine the effect of a variation of FLD on the composite elastic properties. Our analysis shows that it is essential to obtain an accurate fiber orientation distribution and a realistic fiber length distribution to accurately predict the composite properties.

[1]  Charles L. Tucker,et al.  Stiffness and thermal expansion predictions for hybrid short fiber composites , 1990 .

[2]  Charles L. Tucker,et al.  An objective model for slow orientation kinetics in concentrated fiber suspensions: Theory and rheological evidence , 2008 .

[3]  Andrei A. Gusev,et al.  Numerical simulation of the effects of volume fraction, aspect ratio and fibre length distribution on the elastic and thermoelastic properties of short fibre composites , 2002 .

[4]  Vlastimil Kunc,et al.  FIBER LENGTH DISTRIBUTION MEASUREMENT FOR LONG GLASS AND CARBON FIBER REINFORCED INJECTION MOLDED THERMOPLASTICS , 2007 .

[5]  C. L. Tucker,et al.  SIMULATION OF COMPRESSION MOLDING FOR FIBER-REINFORCED THERMOSETTING POLYMERS. , 1984 .

[6]  Charles L. Tucker,et al.  Stiffness Predictions for Unidirectional Short-Fiber Composites: Review and Evaluation , 1999 .

[7]  J. D. Eshelby.  The determination of the elastic field of an ellipsoidal inclusion, and related problems , 1957, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[8]  A. Zanobini,et al.  The Principle of Maximum Entropy Applied in the Evaluation of the Measurement Uncertainty , 2006 .

[9]  W. Chin,et al.  Effects of fiber length and orientation distribution on the elastic modulus of short fiber reinforced thermoplastics , 1988 .

[10]  I. Ward,et al.  Hydrostatically extruded glass fiber reinforced polyoxymethylene. II: Modeling the elastic properties , 1997 .

[11]  G. P. Tandon,et al.  The effect of aspect ratio of inclusions on the elastic properties of unidirectionally aligned composites , 1984 .

[12]  Suresh G. Advani,et al.  The Use of Tensors to Describe and Predict Fiber Orientation in Short Fiber Composites , 1987 .

[13]  Charles L. Tucker,et al.  Fiber orientation in simple injection moldings. Part I: Theory and numerical methods , 1991 .

[14]  Y. Benveniste,et al.  A new approach to the application of Mori-Tanaka's theory in composite materials , 1987 .

[15]  A. A. Gusev,et al.  On the possibility of reduced variable predictions for the thermoelastic properties of short fibre composites , 2004 .

[16]  M. Taya,et al.  On Stiffness and Strength of an Aligned Short-Fiber Reinforced Composite Containing Fiber-End Cracks Under Uniaxial Applied Stress , 1981 .

[17]  E. Silverman.  Effect of glass fiber length on the creep and impact resistance of reinforced thermoplastics , 1987 .

[18]  Chiang-Ho Cheng,et al.  Effective elastic moduli of misoriented short-fiber composites , 1996 .

[19]  R. K. Mittal,et al.  Some studies on glass fiber‐reinforced polypropylene. Part II: Mechanical properties and their dependence on fiber length, interfacial adhesion, and fiber dispersion , 1989 .

[20]  Charles L. Tucker,et al.  Orthotropic closure approximations for flow-induced fiber orientation , 1995 .

[21]  K. Tanaka,et al.  Average stress in matrix and average elastic energy of materials with misfitting inclusions , 1973 .

[22]  E. Wetzel.  Modeling Flow-Induced Microstructure of Inhomogeneous Liquid-Liquid Mixtures , 1999 .

[23]  T. Vu-khanh,et al.  The effects of injection molding on the mechanical behavior of long-fiber reinforced PBT/PET blends , 1991 .

[24]  Frank Henning,et al.  LFTs for automotive applications , 2005 .

[25]  S. Toll,et al.  Microstructure of long-and short-fiber reinforced injection molded polyamide , 1993 .

[26]  C. L. Tucker,et al.  Orientation Behavior of Fibers in Concentrated Suspensions , 1984 .

[27]  H. Fritz,et al.  Injection molding of long fiber‐reinforced thermoplastics: A comparison of extruded and pultruded materials with direct addition of roving strands , 1991 .

[28]  Peter Hine,et al.  Hydrostatically extruded glass‐fiber‐reinforced polyoxymethylene. I: The development of fiber and matrix orientation , 1996 .

[29]  R. K. Mittal,et al.  Some studies on glass fiber‐reinforced polypropylene. Part I: Reduction in fiber length during processing , 1989 .