Fabrication and characterization of polycrystalline SiC resonators

This paper presents the development of polycrystalline 3C silicon carbide (polySiC) lateral resonant devices, which are fabricated by a three-mask surface micromachining process using silicon dioxide (SiO/sub 2/), polysilicon, and nickel (Ni) as the isolation, sacrificial, and contact metallization layers, respectively. The polySiC resonators are packaged for operation in high temperature environments using ceramic-based materials and nickel wirebonding procedures. Device operation is successfully demonstrated over 100 000 at <10/sup -5/ torr and resonant frequency drifts of <18 ppm/h under continuous operation are achieved using an scanning electron microscope (SEM) setup. Device resonant frequency varies nonlinearly with increasing operating temperature. Finite element modeling reveals that this variation resulted from the interplay between the Young's modulus of polySiC and induced stresses, which occur due to mismatch in thermal expansion coefficients of the polySiC film and the underlying silicon (Si) substrate.

[1]  R. Mullen,et al.  Mechanical properties of thick, surface micromachined polysilicon films , 1996, Proceedings of Ninth International Workshop on Micro Electromechanical Systems.

[2]  Shuvo Roy,et al.  High-temperature testing of nickel wire bonds for SiC devices , 1999, Smart Materials, Nano-, and Micro- Smart Systems.

[3]  J. Greenwood,et al.  A high accuracy resonant pressure sensor by fusion bonding and trench etching , 1999 .

[4]  M. Mehregany,et al.  Surface Micromachining of Polycrystalline SiC Deposited on SiO2 by APCVD , 1997 .

[5]  A. Fleischman,et al.  Characterization of polycrystalline silicon carbide films grown by atmospheric pressure chemical vapor deposition on polycrystalline silicon , 1998 .

[6]  C. Nguyen.  High-Q micromechanical oscillators and filters for communications , 1997, Proceedings of 1997 IEEE International Symposium on Circuits and Systems. Circuits and Systems in the Information Age ISCAS '97.

[7]  Mehran Mehregany,et al.  Roughness Reduction of 3C‐SiC Surfaces Using SiC‐Based Mechanical Polishing Slurries , 1999 .

[8]  R. Howe,et al.  Young's Modulus Of In Situ Phosphorus-doped Polysilicon , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[9]  G. Krotz,et al.  Silicon Carbide As A Mechanical Material , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[10]  Mehran Mehregany,et al.  Design, Operation, and Modeling of a Vertical APCVD Reactor for Silicon Carbide Film Growth , 1998 .

[11]  William C. Tang,et al.  Electrostatic Comb Drive for Resonant Sensor and Actuator Applications , 1990 .

[12]  Mehran Mehregany,et al.  Etching of 3C-SiC using CHF3/O2 and CHF3/O2/He plasmas at 1.75 Torr , 1998 .

[13]  G. L. Pearson,et al.  Deformation and fracture of small silicon crystals , 1957 .

[14]  Micromechanical Signal Processors , 1994 .

[15]  R. Reeber,et al.  Thermal expansion and lattice parameters of group IV semiconductors , 1996 .

[16]  M. Mehregany,et al.  Modeling of SiC Lateral Resonant Devices Over a Broad Temperature Range , 1999 .

[17]  A. Fleischman,et al.  Epitaxial growth of 3C–SiC films on 4 in. diam (100) silicon wafers by atmospheric pressure chemical vapor deposition , 1995 .

[18]  Thermal Expansion of β-Sic, Gap and Inp , 1995 .

[19]  M. Offenberg,et al.  A surface micromachined silicon gyroscope using a thick polysilicon layer , 1999, Technical Digest. IEEE International MEMS 99 Conference. Twelfth IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.99CH36291).

[20]  A. Fleischman,et al.  Behaviour of Polycrystalline SiC and Si Surface-Micromachined Lateral Resonant Structures at Elevated Temperatures , 1997 .

[21]  R. Howe,et al.  CMOS micromechanical resonator oscillator , 1993, Proceedings of IEEE International Electron Devices Meeting.